Inorganic chemistry

4.0 INTRODUCTION TO RESULT AND DISCUSSION This chapter covers the result and also the discussion on the experiment of lab scale soap production. All of the findings which are the analysis of pH value, saponification value and moisture content of the formulation soap bar is discussed thoroughly throughout the chapter. 4.1 RESULT AND DISCUSSION The purposes of the experiment were to identify the weights of materials to be used in the formulation of soap and also to produce the average quality…

Experiment 1 and 2 Recrystallization: Purification of Solids and Melting points Purpose: In the fist experiment, impure Vanillin was purified through the process of recrystallization. Desired solutes were recovered through the technique of vacuum filtration, and then dried to take percent recovery In the second experiment, a percent recovery of the recrystallized Vanillin from the first experiment was performed. The percent recovery of Vanillin was 77.18% A mixed…

According to R.A Aitken, “An asymmetric synthesis may be defined as a synthesis in which an achiral unit is an ensemble of substrate molecules is converted to a chiral unit such that the possible stereoisomers are formed in unequal amounts.” It relates to any synthetic process that incorporates one or more new elements of chirality during a functional group transformation. Asymmetric synthesis involves the formation of chiral molecules. An object is said to be chiral, if it cannot be…

TRIS Hcl, NBT, NADH, Ethanol, PMS, l-ascorbic acid 1. The superoxide radicals is generated in 3 ml of TrisHCl buffer (16 mM, pH 8.0) containing 1 ml of NBT (50 μM), 1 ml NADH (78 μM) and ethanol extract of sample (25 – 50 μg). 2. The reaction was started by adding 1 ml of PMS solution (10 μM) to the mixture. 3. The reaction mixture was incubated at 25° C for 5 min, the absorbance was read at 560 nm using a spectrophotometer (Schimadzu UV-Vis 1700) against blank samples using l- ascorbic acid…

2. Basic theories and principles 2.1 Chemical vapor deposition 2.1.1 Definition of chemical vapor deposition Chemical vapor deposition (CVD) is a versatile process which is widely applied to produce coatings, powders, fibers and monolithic components [1]. Applying the chemical vapor deposition, it is possible to produce alloy and compounds of metals and nonmetal materials. Chemical vapor deposition can be defined as the deposition of a solid on a heated surface from a chemical reaction in the…

Salts and molecules have similar characteristics, and many differences whether we can tell by first looks or not. Testing these two only supports the differences, and many structural functions cause these differences. Since salts are ionically bonded, they have different properties and functions compared to the covalent bonded molecules. Salts have a ionic bond, and we can confirm due to their electronegativity. As you move from left to right on the periodic table you would notice that…

The unique composition and purity of as-deposited SnS2 thin films prepared with different precursor solution volumes from 5 ml to 25ml were determined by EDX analysis as shown in fig 5, which brought out the presence of Tin and Sulfur as elementary components. Two different peaks were observed in the spectrums from fig 5 relevant to the tin and sulfur. The EDX spectra show that the weight percentage for the film prepared at the precursor solution volume of 5 ml is 36.8% and 63.2%, which is…

Table 1: Experimental data for standardization of iodine solution. Calculation of standardization factor Standardization factor = (mass of vitamin C titrated) / (Volume of iodine solution used) = (125g) / (41.3ml) = 3.03 mg vitamin C/ml iodine solution Experiment B: Vitamin C titration using fresh fruit sample to determine the content The tabulated experimental data for this experiment is shown below (Table 2). In this experiment, the amount of vitamin C was calculated by multiplying…

What is Styrofoam? Styrofoam is a brand of closed-cell extruded polystyrene foam currently created for thermal insulation and craft applications. Dow Chemical Company retained and produced the Styrofoam. Through petroleum product known as styrene, Styrofoam was created. The styrene is amended into a clear molten mass of polystyrene through a complex chemical process known as polymerization. It would become a hard plastic if it were left to cool. Disposable eating utensils are created from this…

Background : Stoichiometry is the relationship between the relative quantities of substances taking part in a reaction or forming a compound, typically a ratio of whole integers. In the lab that I did with my group we used stoichiometry to find out the decomposition of sodium biocarbonate. Sodium carbonate is just another name for baking soda, and that is what we used on our lab. Baking soda is also used in some food items, such as pancakes, waffles etc… When the baking soda is being heated…