Flammable liquid

Density of Sand The objective of this lab is to use knowledge from previous labs, like the density of water and solids lab, and apply it to find the density of sand. First you must weigh your graduated cylinder, and record the weight, then pour in whatever amount of sand you choose. You then must weigh that to find the mass, and subtract whatever you got by the mass of the graduated cylinder. After that you pour in some water, and find the difference of how much the water went up and, what the…

The purpose of this research paper was to determine the influence of cellulose and date palm pad on cooling efficiency, low cost, and reduced temperatures. A study was undertaken to compare the two types of pads to determine the cooling efficiency, low cost, and reduced temperatures. The study found that cellulose pads gave high cooling efficiency, but at the same time increased the total cost. Date palm pads saved water compared to cellulose pads. The cost of using the date palm pad was less…

Note this: do not use regular magnets because they do not have the strength to attract the slime. Mix the liquid starch and iron oxide powder in the bowl and stir with the craft sticks until they are mixed perfectly. Add the glue and keep stirring. Take the slime out and start squishing until it is perfectly mixed together. You may wear gloves to avoid staining…

INTRODUCTION Chemically and thermodynamically foam is an unstable, dispersed system of entrapment of gaseous molecules in solid or liquid matter. Instability of foam is caused generally due to coalescence, liquid drainage and disproportion of bubbles. Foam being aqueous system can be produced using surfactants available commercially. The types of surfactants used in preparation of aqueous foam influence the foam properties (Eisner et al., 2007; Bhakta and Ruckenstein, 1995). Successful foam…

Facts about Tech Diving You Should Know The conventional limit exceeded by the form of scuba diving specially the recreational diving’s bottom time and depth is known as tech diving. It is also known as Technical Diving. The Technical and Recreational Scuba Diving can be distinguished with lots of differences. According to many people, there are not any obvious differences between Tech and Recreational Diving. They think that ‘diving is diving’ and it is useless to divide it into different types…

All fluids have its resistance to relative motion between surfaces and is called Viscosity. This property is about the friction between the particles of a fluid. A fluid that is forced in a tube has the liquid moving faster as it is closer the axis of the tube and slower when farther from it. 3.1.1 Dimensionless Parameters In analysis of convection heat transfer, it is convenient to convert to non-dimensional the governing equations and combine the variables, which makes the group of…

Friction loss is defined as the pressure loss or head loss that usually occurs in pipeline fluid flow because of the viscosity effect near the surface of the pipe. When the fluid flows along the pipeline, it produces frictional resistance thus results in loss of energy or total head loss of the fluid. Therefore, experiment was conducted to verify the Darcy Weisbach equation by determining the pressure loss along a horizontal pipe. Figure A below shows the diagram of friction loss along a…

Definition: An orifice plate is a device that is used for the measurement of flow rate for reducing pressure or for the restricting flow. An orifice plate is a thin plate with a hole in it, which is usually placed in a pipe. When a fluid (either liquid or gaseous) passes through the orifice, its pressure builds up slightly upstream of the orifice. But as the fluid is forced to converge to pass through the hole, the velocity increases & the fluid pressure decreases. Orifice Plate is the heart of…

4.6 The Selection of the Injection Machine 4.6.1 Calculation of the Injection Volume Figure 4-8 shows the volume of plastic parts by Solidworks modeling. Figure 4-8 Volume of the Stress Cone Plastic parts volume: Vplastic = 4.198 × 10-5 m3 = 41.98 cm3 Plastic parts density: ρ = 1.2 g/cm3 Plastic parts quality: mplastic = ρVplastic = 1.2 × 41.98 = 50.376 g 4.6.2 Preliminary Estimation of the Gating System Although the gating system of condensate cannot determine the exact value prior…

The Evaporation of Liquids When a liquid is left in a warm car over a certain period of time some people might notice that the liquid seems to have lessened. This is because of evaporation, evaporation is when a liquid changes into a gas because of an increase in temperature or pressure. This brings up many questions having to do with liquids and evaporation so, do all liquids take the same amount of time to evaporate? Why do different liquids have…