Exothermic reaction

Phase Solubility results The phase-solubility diagram (figure 1) obtained was classified as AL type(20) because the apparent solubility of ISH increased linearly with β-CD concentration over the entire concentration range studies, thereby suggesting the formation of a water soluble complex. A slope value of less than one indicated that an inclusion complex in a molar stoichiometric ratio of 1:1 was formed between the drug and β-CD in solution. The stability constant (718.58 M–1), computed from…

Most corrosion is an electrochemical reaction. Anything that affects the speed of the chemical reaction will in turn affect the amount of current flow, which will affect the rate of corrosion. The rate of corrosion is directly proportional to the amount of current in the electrochemical corrosion cell. If the current can be measured accurately, then an exact calculation of the metal loss can be made. 2.2.1 ELECTRICAL EFFECTS ON THE RATE OF CORROSION Any issue that have an effect on the…

reconstruction. Hence, understanding the mechanism of exchange and determination of rate of mineral-fluid exchange in foraminiferal calcite are critical for accurate estimation of the extent of post-formational alterations on carbonate-based proxies. The reaction rates estimated in most of the atom exchange experiments are under the basic assumption of homogeneous exchange at equilibrium (illustrated in the Appendix C, section C1) (e.g., Moller and…

help catalyze numerous reactions in the body. They are an arrangement of proteins designed to serve very specific roles. Enzymes contain active sites that substrates bind to. The enzymes then help orient those substrates so they achieve ideal reaction conditions. As a result, substrates are broken down much faster than they would on their own (Lawless 2016). Due to the fact that so many different arrangements of proteins are possible, it’s no surprise that so many reactions in the body are all…

Part one Make a 3 list of chemical safety hazards? The three chemical safety hazards are: Poison Toxic Corrosive Reactive Environmental hazards 2. What is Amalgam? Amalgam is mixture of metals of mercury with another metal and other metal. Almost all metal can be an amalgam with a form of mercury. 3. If you had to train someone on how to separate the mercury from the amalgam, what training would they need? WHY? If I had to train someone on how to separate the mercury…

What is a chemist? A chemist is a scientist that studies, physical and chemical properties of different forms of matter. There are two profound chemist whose findings were crucial to today's understanding of chemistry. There names were Marie Curie and Dimitri Mendeleev, both chemist made significant impacts on modern day science and society. Dmitri Mendeleev is responsible for the creation of the periodic table, while Marie Curie is responsible for discovering radioactivity, which advanced the…

The Rate of Chemical Reaction and the Factors Affecting Reaction Rates The purpose of these labs is to investigate and determine how three factors- concentration, temperature, and a catalyst- affect the rate of a chemical reaction. In the first lab, “Rate of Chemical Reaction,” 1 x 8-well micro strips were used to combine a potassium iodate solution and a sodium meta-bisulfite solution under different conditions; each trial was timed from the point of the first visible reaction until the last…

Subject: Science Concept: Solid, liquid, or gas Sunshine State Standards/Access Points/Common Core: SC.2.P.8.2- Identify objects as solid, liquid, or gas. Primary Instructional Objectives: - Students will be able to identify what the difference is between a solid, liquid, and gas. - Students will be able to identify examples of solids, liquids, and gasses. - Students will be able to sort objects by whether they are solid, liquid, or gas. - Students will be able to define matter and where you…

The 'Wingate Cycle Ergometer Test' is an anaerobic test that is performed on a cycle ergometer. Eg. Monark. (Vandewalle et al. 1987). The aim of our test is to measure Peak Power Output(PPO), Relative Peak Power Output(RPP), Fatigue Index(FI) and Anaerobic Capacity(AC) throughout the Wingate Anaerobic Test. For both our participants we will compare our findings and provide an explanation for the similarities/differences we encounter between the two. Peak Power Output is the highest power output…

Result and discussion: Substrate specificity The substrate specificity for the PPO is represented in table. The Km values for catechol, L-DOPA, L-tyrosine, and p-Cresol are 4.12 × 10-3, 16.4 × 10-3, 6.12 × 10-3, and 5.01 × 10-3, respectively. Catechol was the best suited substrate, having the lowest Km value and highest Vmax value when compared to other 3 substrates (Table 1). Table 1: Substrate specificity of PPO enzyme Substrates Specific activity (units mg-1 protein) Km (µM) Vmax (abs min-1)…