Alternating current

Conclusions • Current ratio is within the industry’s healthy range but ideally should be over 2. There has been a sufficient decrease in current ratio in comparison to the previous year indicating your business may have problems meeting your short-term obligations. • Quick ratio is below the industry average and decreased from the previous year. The business does not have enough adequate current assets, without inventory, to cover short-term debt. • Inventory…

In this experiment, various electrochemical cells were measured and calculated to determine their electrical cell potential. In the electrochemical cell Zn (s) │Zn2+ (0.10 M) ││ Cu2+ (0.10 M) │ Cu(s), E cell potential was determined to be 1.040 V while the standard E˚ cell potential was 1.10 V. In the electrochemical cell Zn (s) │Zn2+ (0.10 M) ││ Cu2+ (1.0 M) │ Cu(s) E cell potential was determined to be 1.060 V while the standard E˚ cell potential was 1.10 V. In the electrochemical cell Cu (s)…

Multimeter: A device used to measure the amount of amperes, volts, and ohms over several ranges of value. Conductor: Object allowing the transfer of electrons Insulator: Prevention of an object receiving an electric current. Resistance: Prevents passage of normal current (light bulb or LED; the object) Parallel: each resistor or light is independent. If one goes out, the rest still stay one. Series: each light is dependent on another one. If one goes out, so do the rest. Scientists discovered…

and 1840s by Samuel Morse, assisted by Alfred Vail. Two inventions helped Morse propel his invention to success. First, in 1800, the Italian physicist Alessandro Volta (1745-1827) invented the battery, which reliably stored an electric current and allowed the current to be used in a controlled environment. Second, in 1820, the Danish physicist Hans Christian Oersted (1777-1851) demonstrated the connection between…

The resistors R1, R2, RD, and RS calculated in the Prelab section were used to connect the circuit as shown in Figure 8-5. A load resistance RL of 10kΩ was used. The values of VD, VG, VS were measured and recorded. 3. The voltage vout was measured using an oscilloscope and the voltage gain AVG-D = vout/vin was calculated. The input voltage was adjusted if the output waveform was distorted. 4. The function generator was varied to obtain the necessary data to plot a frequency response curve for…

therapy and so I wanted to know more on the topic. The article says that 2/5ths of the patients and relatives primary source of information on ECT, comes from (movies, television, newspapers, books, and magazines). What would need to happen for the current acceptance of this treatment procedure to…

Background Information Electricity is a form of energy resulting from the build-up of charged particles, either statically as an accumulation of charge or dynamically as a current (Oxford dictionary, 2015). The effect of electricity can be seen in play daily, whether through a simple light bulb, or a complex application such as providing energy to a power plant. It is often stated that electricity is the most versatile and easily controlled form of energy, and at the point of use it is…

for lenders. Additionally, the company’s current ratio, a ratio that divided current assets by current liabilities to show a businesses ability to meet its current obligations, is currently a strong 5.99 (Appendix 1). Also, the current ratio has increased every month for the past seven months (Oct. 1990-March 1991, excel sheet). The current ratio suggests that Dynashears is currently in good financial standing, and that there ability to meet their current obligations is improving. However, there…

But in Norton’s Theorem the equivalent circuit has a current source and a resistance in parallel with the load resistance (R_X). Continued on next page: HOW IS IT USED When using Norton’s Theorem the load resistance is removed and replaced with a short (wire) and points labeled A and B. The reason to label the points A and B is to show where the meter would measure the unknown voltage and current associated with the load resistance. Next the load resistor is placed into…

material resists current, and is measured in Ohm-meters (Ω-m). Electrical resistance (R) is the opposite of the flow of electrons, or the passage of an electrical current. Electrical conductivity (σ) is the opposite of resistivity and is measured in Siemens (S). Electrical conductivity is defined as; the degree to which a specified material conducts electricity, calculated as the ratio of the current density in the material to the electric field which causes the flow of current. In this…