Ures

Front 1

What does the M character designate in the 2M0XX career field?

Back 1

Missile maintenance

Front 2

Where do the SNCOs in your career field derive the information to develop the SKT?

Back 2

Career development course

Front 3

Which of the following is not a function of the career field education training plan?

Back 3

Tracks ancillary training

Front 4

According to documentation in the CFETP what requirements must you meet to be awarded your 7-skill level?

Back 4

Be certified on all 7 level core tasks, and complete your craftsman CDC

Front 5

Who is responsible for inspecting troubleshooting and repairing hoists as well as certifying pneumatic and hydraulic components?

Back 5

MAPS

Front 6

Which statement best explains the authority to launch ICBMs?

Back 6

The president has the authority to launch a missile attack but AfGSC has the means of delivery

Front 7

Remove and replace maintenance performes at the LF and LCC minimizes the ICBM weapon system downtime and contributes to which strategic characteristic?

Back 7

High in commission rate

Front 8

What combination of LCCs and LFs make up one missile flight

Back 8

One LCC 10 LFs

Front 9

How many LFs can a LCC control?

Back 9

All those in it's squadron

Front 10

The necessary thrust to launch a MinuteMan 3 missile into a prescribed trajectory is provided by

Back 10

3 stage solid propellant booster

Front 11

What is used to drive the exhaust gas generator in the MinuteMan 3 second stage motor in order to accomplish missile roll?

Back 11

Solid fuel exhaust gases

Front 12

Which components aerodynamically join the MinuteMan 3 motor stages and provide stage separation?

Back 12

Aluminum alloy interstages

Front 13

The RS shroud assembly is separated by a rocket motor located in the

Back 13

Forward shroud

Front 14

What component in the MGS provides reports of missile and ground equipment status during ground operations?

Back 14

Missile guidance computer

Front 15

What feature prevents incorrect mating of the fill valves to the PSRE oxidizer and fuel storage tanks?

Back 15

Difference in the fill and drain fittings on each storage tank

Front 16

What area/facilities would you find in the missile support area?

Back 16

Weapons storage area, missile transfer building, and proofload test facility

Front 17

The primary method used for shipping missile downstages from depot to the missile transfer building is by

Back 17

Road or highway in a missile transporter

Front 18

What is the primary mission of a MAF?

Back 18

Housing the missile combat crew officers

Front 19

If personnel are requesting access to the LCC the

Back 19

SCC must positively identify and authorize all personnel

Front 20

All air that enters the MAF clean room must pass through a

Back 20

CBR filter

Front 21

How is vertical movement of the launcher closure door prevented

Back 21

Mated beveled edges and weight

Front 22

What design feature permits limited motion between the launch tube and equipment room without danger of major structural damage

Back 22

6-8 inch rattle space

Front 23

What component is lowered to gain access to the upper LER

Back 23

Secondary door

Front 24

What two activities merged together to form AFGSC?

Back 24

ICBM forces and longer range bomber assets

Front 25

The AFGSC mission supports the US

Back 25

President and combatant commanders

Front 26

The 8th AF plans and executes nuclear deterrence through the use of

Back 26

Long range bombers

Front 27

What combatant command does the 20th AF fall under as Task Force 214?

Back 27

USSTRATCOM

Front 28

What 20th AF logistics division section puts together maintenance data analysis and generates weapon system metrics?

Back 28

ICBM readiness

Front 29

What 20th AF unit operates the ICBM center of excellence?

Back 29

620th missile operations flight

Front 30

The first level of command where all of the subordinate levels of command are located on the same installation is known as a

Back 30

Wing

Front 31

A typical missile wing is comprised of

Back 31

Operations, mission support, and medical groups

Front 32

Each squadron in the operations group is responsible for

Back 32

Monitoring and controlling 50 LFs and 5 MAFs

Front 33

When a periodic maintenance schedule is set each year it should not deviate by more than

Back 33

60 days

Front 34

The plans and scheduling section holds daily meetings to

Back 34

Coordinate the next days actions

Front 35

The MMOC ensures maintenance teams do not exceed their timelines by

Back 35

Tracking teams arrival and departure times

Front 36

What section provides central oversight over all IMDS related functions?

Back 36

Data analysis

Front 37

What is MAPS responsible for regarding the proofload test facility?

Back 37

Operations and maintenance

Front 38

VES must maintain records of?

Back 38

Inspections and calibrations of equipment

Front 39

One purpose of a FMT team is to

Back 39

Replace brine chillers

Front 40

While on a LF an EMT might perform

Back 40

Repairs on emergency storage batteries

Front 41

The verification and checkout equipment course provides training on how to

Back 41

Operate specialized equipment that gathers data from an air launched cruise missile

Front 42

Who is in command of the LF and MAF at all times?

Back 42

Missile combat crew

Front 43

Who serves as the maintenance groups focal point for enlisted Manning?

Back 43

Maintenance group commander

Front 44

What must the NCOIC provide to VES for known maintenance dispatches?

Back 44

Equipment load lists

Front 45

To support US military operations and national security objectives spacelift operations are conducted to augment or reconstitute space based capabilities along with providing for their

Back 45

Deployment and sustainment

Front 46

Who is responsible for making sure assigned spacelift and support equipment remains safe serviceable and properly configured to meet mission needs?

Back 46

SMT

Front 47

What subsystem provides a mechanical base for the satellite vehicle?

Back 47

Structural

Front 48

What directs the exhaust plume of the launch vehicle away from sensitive ground support equipment

Back 48

Flame trench

Front 49

Final assembling of the satellite vehicle is performed in the

Back 49

Payload processing facility PPF

Front 50

What AFRL directorate finds new ways to strike the enemy through aerospace avenues?

Back 50

Air vehicles

Front 51

What is the period called when critical functions are in a state of readiness without dependence on normal environment control support?

Back 51

Emergency survival

Front 52

What would be an example of a hardness critical item that protects other equipment performing a hardness critical function

Back 52

Shock isolators

Front 53

A large percentage of energy from a nuclear detonation results in

Back 53

Air blast effects

Front 54

Which characteristic greatly influences EMP at the LER liner?

Back 54

Conduit shielding

Front 55

Over one third of the energy from a nuclear explosion is emitted in the form of

Back 55

Heat and light

Front 56

What circuit protection holds the operations of a mission critical circuit in a known operating mode until after EMP or radiation has subsided

Back 56

Circumvention/reset

Front 57

What type of shock isolators do the Wing 3 and 5 LCCs use

Back 57

Air filled pendulum

Front 58

What do penetrating lines act as to direct EMP into the LCC?

Back 58

An antenna

Front 59

How is installed equipment that generally considered to be fragile or of high value to the weapon system installed?

Back 59

Shock mounted

Front 60

Who can provide technical assistance for all installation hardware or maintenance requirements not specifically covered in TOs or CE manuals?

Back 60

Ogden air logistics complex

Front 61

When installing an ESA vault RFI gasket what percentage of the gaskets width must be in contact with the hatch cover

Back 61

75%

Front 62

Which deficiency report classification would be appropriate if the reported defect is likely to result in failure?

Back 62

Major

Front 63

Which is an example of a product quality deficiency?

Back 63

When a component is installed and fails right away

Front 64

What deficiency report category is used for deficiencies that might hinder the maintenance process but allows job completion?

Back 64

Category II

Front 65

What step in the deficiency reporting process reviews deficiency reports for proper categorization validity correctness of entries and accuracy?

Back 65

Screening point

Front 66

Which operational event phase of the IMDS subsystem provides the capability for periodic reports of mission accomplishment?

Back 66

3

Front 67

What process provides maintenance managers at all levels with information on jobs performed by each workcenter

Back 67

Maintenance data documentation process

Front 68

What term is annotated in the cert status of the MNCL

Back 68

Nuclear or design

Front 69

At what organizational level are operating instructions developed for use?

Back 69

Unit

Front 70

What information does a an inspection work card contain?

Back 70

Specific pass or fail criteria

Front 71

Before a preliminary TO can be used for maintenance on the weapon system it must

Back 71

Have it's procedures verified with oversight from the technical content manager

Front 72

What determines how a technical order will be numbered?

Back 72

The first set of numbers/letters that identify the category

Front 73

What information is located in the bottom right hand corner of a TOs title

Back 73

The latest change number and the date it was published

Front 74

What important information is contained in the component replacement and adjustment table of a TO?

Back 74

What mode of operation the system must be in

Front 75

What two types of CE manuals are used together?

Back 75

System and equipment

Front 76

What information is provided in a civil engineering manual master change log?

Back 76

Procedures for performing one time inspections

Front 77

CE manual improvement reports are submitted for all except

Back 77

Temporarily bypassing system components

Front 78

What information is entered into block 2 of an AFGSC form 272?

Back 78

TODO or TMCM office symbol and mailing address

Front 79

What information is entered into block 6 of a AFGSC form 272?

Back 79

Page or range of pages that will be changed

Front 80

What information is entered into block 9 of a AFGSC form 272?

Back 80

A description of the deficiency

Front 81

Who completes block 11a of a AFGSC form 272?

Back 81

QA evaluator

Front 82

Upon what principle does a hydraulic system operate?

Back 82

Force is distributed equally throughout a contained body of liquid

Front 83

PT hoist has a maximum lifting capacity of

Back 83

3000 lbs

Front 84

The inch button lowers how much of the hoist

Back 84

0.030 inch

Front 85

The TE tractor PTO unit

Back 85

Drives the auxiliary hydraulic pump

Front 86

The TE APU preheated elements need to be energized for 30 seconds prior to starting in cold weather to preheat the

Back 86

Intake air

Front 87

What is the purpose of the TE rail restraints

Back 87

Secure the downstage during transport

Front 88

The TE emergency flow limiter manifold prevents the

Back 88

Container from freefalling if a hydraulic line fails

Front 89

Identify the purpose of the MT semitrailers front and rear access doors

Back 89

Provide for missile loading and unloading

Front 90

The MT semitrailer winch is used for

Back 90

Loading and unloading a downstage from the semitrailer

Front 91

The purpose of the hydraulic pressure charging set is to service the

Back 91

Shock isolators and the MSS with silicon fluid

Front 92

Select the purpose of the hydraulic purge set

Back 92

Collect fluid samples from or decontaminate the TE hydraulic system

Front 93

Identify the purpose of the CVA control unit

Back 93

Direct the flow of nitrogen gas from the regulator to the LC actuator cylinder

Front 94

The PAC controls the temperature and humidity of the

Back 94

MT and TE

Front 95

Why is the missile grounded during downstage handling operations

Back 95

Components are sensitive to ESD

Front 96

Identify the purpose of the shipping links that are installed on the first stage nozzles during transit

Back 96

Keep nozzles in a fixed position to avoid possible damage

Front 97

The missile sensaphone monitoring system monitors the environment inside the container the missile is stored in and automatically

Back 97

Dials a phone number if the temperature is out of tolerance

Front 98

Identify the purpose of the leveling jacks used by MHT

Back 98

Adjustment of TE and MT containers prior to a roll transfer

Front 99

The optical alignment set used by MHT ensures the

Back 99

Alignment of the TE and MT containers prior to a roll transfer

Front 100

The skirt umbilical provides

Back 100

A pathway for electrical signals and power to flow between the D-Box and the first and second stage missile boosters

Front 101

When the lower umbilical is disconnected from the missile the MCC will

Back 101

Receive a missile away indication from that LF

Front 102

What is the first step of a LF shutdown

Back 102

Verify the SCS is locked and the safe arm indicator shows S

Front 103

Identify the first step of LSB electrical isolation

Back 103

Place the MPP power switch to off

Front 104

What is the recovery strap used for when accomplishing forced entry procedures following a b plug lockout

Back 104

Prevent the cable pin from falling onto the missile

Front 105

How is the down stage lowered and raised

Back 105

Through the use of four sling rods that are bolted to the downstairs adapter ring in the TE

Front 106

What does the first stage motor consist of

Back 106

Steel case with aft closure, 4 nozzles, and solid propellant 6 point hollow core design

Front 107

What does the second stage motor consist of

Back 107

Titanium alloy motor case. One nozzle, thrust vector control system

Front 108

What does the 3rd stage motor consist of

Back 108

Fiberglass two nozzles and thrust termination ports

Front 109

AFTO 22 emergency priority is when

Back 109

If not corrected would result in a fatality or serious injury to personnel or extensive damage

Front 110

How many gallons in the TE hydraulic reservoir

Back 110

115 main 10 auxiliary