Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
50 Cards in this Set
- Front
- Back
|
What are the three basic cuts of a file? |
Single-cut Double-cut Curved tooth |
|
|
The three rules of tool maintenance are? |
Clean Oil Replace |
|
|
Employees with less than 6 months experience are __ times more likely to be injured than employees with one year or more experience. |
3 times more likely |
|
|
The fall arrest system should not allow a fall of more than: |
1.8 meters/6 feet |
|
|
What are the elements of the fire triangle? |
Air Fuel Ignition (heat) |
|
|
What does PASS stand for? |
Pull the pin Aim the nozzle Squeeze handle Sweep the nozzle |
|
|
What is the depth of the V-notch on a set of hand notchers? |
3/4” |
|
|
What does TPI stand for? |
Teeth per inch |
|
|
What is a portable hand punch also called? |
Whitney punch |
|
|
What is the point angle on a centre punch? |
90° |
|
|
What are the five parts of a hammer? |
Face Post Eye Peen Handle |
|
|
What determines the size of plier types? |
Overall length |
|
|
What are the terms of how the coarseness of a file is graded? |
Rough Coarse Bastard Second-cut Smooth Dead smooth |
|
|
When rotary machines are fitted with rolls they are called: |
Turning machines |
|
|
What is another name for the Throatless bench shear? |
Beverly shear |
|
|
What is the capacity on a bar folder? |
22 gauge |
|
|
What are the four workplace hazard categories? |
Biological Chemical Physical Ergonomic |
|
|
Which stake is used to form conical projects? |
Blowhorn stake |
|
|
How is the size of a bench vice determined? |
By the size of its jaws |
|
|
What are the three parts of a twist drill/drill bit? |
Point Body Shank |
|
|
What is the angle of the point on a general purpose drill bit? |
118° |
|
|
What is the angle of a full V-notch? |
90° |
|
|
What is the total thickness of the material being joined when riveting called? |
Grip range |
|
|
What are the properties of metal? |
Brittleness Conductivity Ductility Elasticity Hardness Malleability Strength Toughness |
|
|
What is Annealing? |
The process of relieving internal stresses in hardened metal by heating the metal to a pre-determined temperature and allowing it to cool |
|
|
What is a ferrous metal? |
A metal that contains iron |
|
|
What is a non ferrous metal? |
Metal that does not contain iron |
|
|
What is the ladder ratio? |
4:1 |
|
|
Thermosetting plastics ______ under heat. |
Harden |
|
|
What is safety factor of rope? |
5:1 on new rope 10:1 on old rope |
|
|
What is the angle of the point on a scratch awl? |
15° |
|
|
What is the metal thickness gauge for ferrous metals? |
US Standard gauge |
|
|
What is the metal thickness gauge for non ferrous metals? |
Brown and Sharpe |
|
|
Which direction do red aviation snips cut? |
Left |
|
|
Which direction do green aviation snips cut? |
Right |
|
|
What is the capacity of bulldog aviation snips? |
16 gauge mild steel |
|
|
What does SMAW stand for? |
Sheet Metal Arc Welding aka stick welding |
|
|
What does GMAW stand for? |
Gas Metal Arc Welding aka MIG welding |
|
|
What does FCAW stand for? |
Flux Cored Arc Welding |
|
|
What does FCAW stand for? |
Flux Cored Arc Welding |
|
|
What does GTAW stand for? |
Gas Tungsten Arc Welding aka TIG (Tungsten Inert Gas) welding |
|
|
What are the three basic malfunctions you can experience with oxyfuel equipment? |
1. Backfires 2. Burnbacks 3. Flashbacks |
|
|
What are fluxes? |
Deoxidization agents aka cleansing agents |
|
|
What does SDR stand for? |
Stop Drop Roll |
|
|
What are the most dangerous type of light rays? |
Infrared Rays |
|
|
What is Natural General Ventilation? |
An unlimited fresh air supply |
|
|
What is mechanical general ventilation? |
When air is pumped into the shop, passes through and is vented outdoors through the ductwork |
|
|
What is mechanical general ventilation? |
When air is pumped into the shop, passes through and is vented outdoors through the ductwork |
|
|
What is local ventilation? |
Exhaust fans capture fumes at their source and exhausts them outdoors aka source extraction |
|
|
When rescuing an electric shock victim if they are still in contact with the conductor: |
Don’t touch them, switch off electrical supply or separate them with a non conductive material such as a wooden 2x4 |
