Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
77 Cards in this Set
- Front
- Back
What is the greatest gas turbine engine asset? |
Power to weight ratio |
|
Within how many days can a GTE be changed out on a frigate or cruiser? |
4 |
|
How many hours would it take for a GTE on a hovercraft to be changed out? |
8 |
|
Which type of cycle does combustion occur at constant pressure? |
Brayton |
|
The type of shaft used on GTE may be what? |
Single, split, or twin spool |
|
What are the two types of compressors? |
Centrifugal flow and axial flow |
|
What are the three types of combustion chambers? |
Can, annular, and can-annular |
|
What are the two types of air seals used in GTEs? |
Labyrinth and honeycomb |
|
What are the three types of oil seals used in GTEs? |
Lip-type, labyrinth/windback, and carbon ring |
|
What are the three types of starters used in GTEs? |
Electric, hydraulic, and pneumatic |
|
How long can the inner wall of the LM2500 withstand a temperature of 2000 degrees? |
15 mins |
|
What is the starter operating air pressure for starting the LM2500? |
35-41 psig |
|
The LM2500 has how many fuel nozzles? |
30 |
|
About what percent of the compressor discharge air entering the combustion section passes to the burner can in the Allison 501k? |
25% |
|
GTG engine speed is measured by what? |
Magnetic pickup |
|
How many and what type of thermocouples are used in the GTG? |
18, chromel-alumel |
|
What type of friction exists between a body at rest and the surface upon which it rests? |
Static |
|
What type of friction exists between moving bodies? |
Kinetic |
|
What is the minimum flash point for lube oil? |
300 degrees |
|
How many hours at a minimum must fuel oil be circulated before a service tank is placed in operation? |
3 hours |
|
Main drainage system has eductors of how many GPM? |
1250 |
|
How many rpm can hovercrafts accelerate to? |
100 |
|
What are the two elements required for proper operation of a GTE? |
Newton's third law and Bernoulli's principle |
|
The two main elements of an axial flow compressor are what? |
A rotor and stator |
|
What are the two main types of axial compressor rotors? |
Disc and drum |
|
The pressure rise of about how many times the preceding stage is about as much as a single stage can handle in a compressor? |
1.2 |
|
What are used to straighten airflow and directed to the first stage rotor? |
Inlet guide vanes |
|
What have the critical function of supporting the main engine rotor? |
Main bearings |
|
What are the high voltage electrical spark producers power from the ignition exciter circuits? |
Spark igniters |
|
The heater in the LM 2500 enclosure maintains air temperature above how many degrees it is not operating to ensure suitable fuel viscosity is maintained for engine starting? |
60 degrees Fahrenheit |
|
Navy GTEs are not rated for operation in ambient temperatures above how many degrees? |
130 degrees Fahrenheit |
|
FOD screen prevents foreign objects larger than how many inches from entering the engine? |
0.25" |
|
Which components direct air from the inlet plenum to the compressor? |
bellmouth and bulletnose |
|
Which type of combustor is the LM2500 combustor? |
Annular |
|
How many disks does the power turbine rotor have with integral disk spacers bolted together to form the rotor spool? |
6 |
|
Air from the ship's start air system is supplied through an inlet fitting on the enclosure base to the starter valve at 0 to what psig? |
75 |
|
What are the two pumping elements of fuel pumps? |
centrifugal boost element and HP gear |
|
Which sensor controls or meters fuel across an orifice? |
compressor inlet temperature (CIT) |
|
Which type of rotary actuator moves the internal components of the main fuel control to control the fuel flow to the engine? |
power level angle (PLA) |
|
Which type of DC generator is directly coupled to the motor shaft and outputs a DC voltage proportional to the motor speed? |
tachometer |
|
Engine vibration is measured by a displacement type of what? |
vibration transducer |
|
Which governor system provides constant speed regardless of load? |
isochronous |
|
Which governor mode regulates speed but will decrease slightly with an increase in load? |
droop |
|
What supplies field excitation to its associated GTE? |
governor control unit (GCU) |
|
Where are the resistance temperature detectors embedded in the generator stator winding slots? |
Babbitt |
|
What are the three types of kinetic friction? |
sliding, rolling, fluid |
|
What is the molecular attraction between particles called that holds a substance or body together? |
cohesion |
|
What is the molecular attraction between particles called that causes unlike surfaces to stick together? |
adhesion |
|
Which oil property is its tendency to resist flow or change of shape? |
viscosity |
|
What are the two types of bowls that centrifugal purifiers used on ships? |
tubular and disc |
|
Which program provides spectrometric analysis of ship's L/O at a designated laboratory? |
navy oil analysis program (NOAP) |
|
What is the last conditioning station before F/O is used in the GTE? |
coalescer |
|
What psi is bleed air regulated at? |
75 |
|
An icing condition exists when the inlet air temperature to a GTE is what? |
41 degrees Fahrenheit or less and 70% humidity or greater |
|
Which type of air system modifies the thrashing noise produced by the ship's propellers to disguise the sonar signature of the propellers? |
prairie |
|
Halon 1301 decomposes on hot surfaces above how many degrees? |
900 degrees Fahrenheit |
|
What will battle override not override? |
PT overspeed trip and flameout |
|
Which system provides centralized and remote monitoring and control of the propulsion, electrical, auxiliary, and damage controls on the arleigh-burke class ship? |
machinery control system (MCS) |
|
Which oil property is its ability to separate cleanly from any water present? |
demulsibility |
|
What is a bowl or hollow cylindrical vessel called that rotates at high speed while liquid passes through it? |
centrifuge |
|
Bleed air is cooled to what temperature and distributed to the masker emitter rings outside the ship's hull on the CG and DD? |
190 degrees Fahrenheit |
|
What are the three systems that make up a ship's drainage system? |
main drainage, secondary drainage, and ballast system |
|
How many manual/hydraulic operated butterfly valves are associated with the SWS? |
9 |
|
Which panel is at the bottom panel of the propulsion control console? |
propulsion control |
|
What is the engine room console on the FFG class ship? |
local operating panel (LOP) |
|
Which high speed printer can print bell commands as well as changes in propulsion system status? |
bell logger |
|
What computer performs centralized monitoring and controlling functions for the console which is embedded in each MCS console? And how many consoles in the MCS have these computers? |
AN/UYK-44/6 |
|
Which tape unit is used as a data logger to record MCS machinery status changes and alarms? |
AN/USH-26(V) |
|
Which panel is used by the EOOW to monitor selected parameters of the engineering plant? |
A2 |
|
Which units provide the local control for LM2500 that drive the shafts and they provide the interfaces with the auxiliary machinery plant? |
SCU |
|
The PACC communicates with the SCU and with other consoles in the MCS over ship's what? |
data multiplexing system (DMS) |
|
Which control system is used on DD class ships? |
electric plant console equipment (EPCE) |
|
How many 60/400hz converters does the DD class ship have? |
3 |
|
How many panels is the EPCC on the FFG divided into? |
9 |
|
How many sections does the rear of the DCC consist of? |
5 |
|
Which system is a general purpose user oriented electronic information transfer system that provides data transfer for the major systems aboard the DDG-51 class ships? |
data multiplex system (DMS) |
|
The bell logger provides an automatic printout each hour or when the propeller RPM or pitch is changes by more that what percent in addition to other events? |
5% |