Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
49 Cards in this Set
- Front
- Back
The chemical used to bond anchors in solid masonry is ____. |
epoxy resin compound |
|
An anchor that has high and low threads that cut into a properly sized hole and does not need a plastic or lead anchor is a ____. |
concrete screw |
|
Fasteners that attach parts to a solid masonry or hollow walls and ceilings are called ____. |
anchors |
|
A deep-threaded anchor used in gypsum board is a ____. |
conical screw |
|
A U-shaped fastener used to secure a variety of materials is a ____. |
staple |
|
Finish nails are most often used to fasten exterior insulation boards. |
False |
|
Nails derive their holding power from the pressure of wood fibres and different types of shanks |
True |
|
When a hole for a wedge anchor is drilled, the hole size is ____. |
the same size as the anchor |
|
Nails have greater holding power than screws. |
False |
|
Nails cut from long rolls of metal wire are called ____. |
wire nails |
|
A(n) ____________________ is used to drive finish nails below the surface. |
nail set |
|
When building a temporary structure such as concrete forms, where the nail must be pried out when the structure is dismantled, use a ____. |
duplex nail |
|
A hole slightly smaller than the plug diameter must be drilled for expansion shields |
False |
|
Anchors that have two sheared expanded halves at the base and are driven in with a hammer are called ____. |
split fast anchors |
|
The anchor that has wings with springs is a ____. |
wing toggle bolt |
|
When using a self-tapping screw, ____. a. use a power screwdriver b. it is not necessary to predrill a hole c. make sure the drilling process is complete before the threading process begins d. all the above |
d. all the above |
|
Fasteners coated with zinc to retard rusting are called ____. |
galvanized |
|
To avoid dark stains around fasteners in certain woods exposed to the weather, ____. |
use stainless steel fasteners |
|
When a nut and bolt are used in wood, a(n) ____________________ should also be used. |
washer |
|
An example of a solid wall anchor is ____.
|
wedge anchor |
|
The adhesive used to attach ceramic wall tile is ____. |
trowelled mastic |
|
A light-duty anchor that consists of an expandable sleeve, a machine screw, and a fibre washer is called ____. |
hollow wall expansion anchor |
|
When a moisture-resistant exterior glue is required, use ____. |
urethane glue |
|
The blunt diamond point on the end of cut nail helps ____. |
prevent splitting the wood |
|
Uncoated steel nails are called ____. |
bright nails |
|
A(n) _______________________ bit is used for recessing screws flush with the surface. |
Countersinking |
|
Brads are a type of ____. |
finish nail |
|
An adhesive used to apply plastic laminates to countertops is ____. |
contact cement |
|
____________________ screws cut threads in metal when driven. |
self-tapping |
|
A disadvantage to using tumble toggle bolts is that ____. |
if removed the toggle falls off the screw inside the wall |
|
The term “connector” refers to a ____. |
metal device used to fasten wood to masonry |
|
To prevent nails from rusting, they are coated with ____. |
zinc |
|
A large screw with a square or hex head designed to be turned with a wrench is a ____. |
lag screw |
|
An adhesive used to eliminate squeaks on stairs is ____. |
construction adhesive |
|
Carpenters yellow glue may be used in exterior applications and is considered waterproof? |
False |
|
____________________ nails are made of hardened steel |
Masonry |
|
A screw that has a bugle shaped head is a ____. |
drywall screw |
|
The three classifications of solid wall anchors are ____. |
heavy, medium, and light-duty |
|
The head of a finish nail is sunk into the wood with ____. |
a nail set |
|
Post and column caps are types of ____. |
connectors |
|
Box nails may be coated with resin cement to ____. |
increase their holding power |
|
The diameter of a nail is called its ____. |
gauge |
|
The hammer drive anchor, aluminum drive anchor, and the nylon nail anchor are types of ____. |
light-duty anchors |
|
Shank and ____________________ holes are drilled to receive lag bolts |
pilot |
|
The reaction between two different kinds of metal and moisture is called ____. |
electrolysis |
|
Sheet metal screws are used for fastening ____. |
thin metal |
|
To allow a screw to turn more easily, ____. |
apply a little wax or soap to the threads of the screw |
|
A bolt with a square section under its oval head is a ____. |
carriage bolt |
|
The nails used for fastening into concrete are called ____. |
masonry nails |