Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
40 Cards in this Set
- Front
- Back
The water in a boiler is heated, turns to steam, and leaves the boiler through the ______________ .
|
main steam line
|
|
When steam releases heat in the heat exchanger, it turns to ______________ .
|
condensate
|
|
What type of pump returns condensate from the system back to the boiler?
|
vacuum
|
|
What valve allows the flow of water in one direction?
|
The check valve
|
|
The feedwater _________ valve should be located as close to the shell of the boiler as practical.
|
stop
|
|
A ________ after each heating unit allows condensate to pass through to the return line.
|
steam trap
|
|
What may be required on some boilers to remove oxygen and other gases?
|
feedwater heater
|
|
The feedwater _____ valve opens and closes automatically.
|
check
|
|
The vacuum pump pumps water and discharges air to the __________ .
|
atmosphere
|
|
The range of pressure on the vacuum switch is usually ___________ .
|
2" to 8"
|
|
The primary function of a low water fuel cutoff is to _________ .
|
shut down the burner if the water level drops below the safe operating level
|
|
Water added to the boiler to replace water lost due to leaks and blowing down is know as _____ water.
|
makeup
|
|
Excessive use of cold city makeup water reduces overall boiler efficiency because the water must be ______ before use in the boiler.
|
heated
|
|
An auxiliary low fuel cutoff is installed ________ .
|
slightly below the primary low water fuel cutoff
|
|
The _____ shuts off the burner in the event of low water.
|
low water fuel cutoff
|
|
Water is supplied to the condensate return tank by the ______ pump.
|
vacuum
|
|
The feedwater regulator is located at the ______.
|
NOWL
|
|
The ________ maintains a constant water level in the boiler.
|
feedwater regulator
|
|
The low water fuel cutoff should be tested ________ .
|
daily
|
|
The burner should be _____ when the low water fuel cutoff is blown down.
|
firing
|
|
A high water level condition in the boiler could lead to water hammer.
|
True
|
|
A low water level condition in the boiler can result in damage to boiler heating surfaces.
|
True
|
|
The check valve on the feedwater line should be located closest to the shell of the boiler.
|
False
|
|
The check valve allows the flow of water in one direction only.
|
True
|
|
The check valve on the feedwater line commonly has a valve disc that swings to open and close the valve.
|
True
|
|
A condensate return tank collects condensate returned from heating units for use in the boiler.
|
True
|
|
A globe valve used as a feedwater stop valve must be installed so inlet pressure is applied from under the valve disc.
|
True
|
|
The stop valve on the feedwater line should be located closest to the boiler.
|
True
|
|
The vacuum pump is designed to discharge air and pump water.
|
True
|
|
Centrifugal feedwater pumps are commonly driven by steam.
|
False
|
|
A check valve is opened by turning the handle counterclockwise.
|
False
|
|
A low water fuel cutoff is located slightly below the NOWL.
|
True
|
|
The range of pressure on the vacuum switch on a vacuum pump is usually 2″ to 8″.
|
True
|
|
An evaporation test is performed by opening the low water fuel cutoff blowdown valve by hand.
|
False
|
|
Any loss of water in the system must be made up by the makeup water feeder.
|
True
|
|
The boiler operator must be present during an evaporation test.
|
True
|
|
The makeup water feeder can be used as feedwater.
|
False
|
|
Most makeup water contains some scale-forming salts.
|
True
|
|
The function of the automatic makeup water feeder is to replace water that has been lost.
|
True
|
|
The automatic city water makeup water feeder is located slightly below the NOWL.
|
True
|