Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
59 Cards in this Set
- Front
- Back
RIPv2 Metric
|
Hop-Count (maximum of 15)
|
|
RIPv2 Metric
|
Hop-Count (maximum of 15)
|
|
OSPF Metric
|
Cost
|
|
HSRP v1 & v2 multicast address
|
224.0.0.2 & 224.0.0.102
|
|
Subnet mask for /26
|
225.225.225.192
|
|
Subnet mask for /30
|
255.255.255.252
|
|
Command to enable IPv6 Routing?
|
(config)#ipv6 unicast-routing
|
|
Standard ACL range
|
1-99 or 1300-1999
|
|
ACL to block traffic from 10.0.0.0 /24 with (config-if)#access-group 14 out
|
(config)#access-list 14 deny 10.0.0.0 0.0.0.255 (Be careful of the deny any statement on all ACL's!)
|
|
Bandwidth of Serial (T1)
|
1544Kbps (1.544Mbps)
|
|
Hello BPDU (Name a few parameters)
|
1) Root Bridge ID 2) Senders Bridge ID 3) Senders Path Cost 4) Timer Intervals (Hello, Forward & MaxAge)
|
|
Does the 'encapsulation ppp' work on an interface like f0/0?
|
No, you use PPPoE (PPP over Ethernet). Client side you will need to configure a dialer interface...
|
|
What is the Administrative Distance of eBGP?
|
20
|
|
What is the Administrative Distance of RIP?
|
120
|
|
Name a few Internal Gateway Protocols
|
RIP, IGRP, EIGRP, OSPF, IS-IS
|
|
Default Hello timer of RIP?
|
30 Seconds
|
|
Command to see the ospf database?
|
R1#show ip ospf database
|
|
Abbrev. of an OSPF router with interfaces in multiple areas?
|
ABR (Area Border Router)
|
|
What does MPLS stand for?
|
Multi Protocol Label Switching
|
|
OSPF Path Cost for a serial link (T1 - 1.544Mbps)?
|
64
|
|
What is EIGRP Reported Distance?
|
The metric from an EIGRP Neighbor to the destination
|
|
What is a EIGRP feasible route?
|
The metric from the local router to the destination
|
|
How can you tell the ethernet frame has a 802.1Q tag?
|
TPID shows 0x8100 (Which defines it as a 802.1Q Tag) along with TCI information...
|
|
Default Bridge ID in Spanning Tree?
|
32768 (VLAN1 is 32769 etc..)
|
|
In the Spanning Tree root bridge election process, what happens if the priority in the Bridge ID ties?
|
They will then compare MAC addresses and use the lowest MAC address.
|
|
Easiest way to choose what switch is elected as the Root Bridge in Spanning Tree for VLAN 10?
|
(config)#spanning-tree vlan 10 root primary
|
|
What is the first thing you would typically configure when creating a GRE tunnel?
|
(config)#interface tunnel 1 - (or any other number)
|
|
Most preferred authentication protocol when using PPP or PPPoE
|
CHAP (Challenge Handshake Authentication Protocol)
|
|
Does a GRE tunnel provide encryption?
|
No, a GRE tunnel is commonly used inside a IPSec tunnel for encryption
|
|
Which RFC defines private IP addresses?
|
RFC 1918
|
|
How many bytes in a 802.1Q header?
|
4 Bytes (32 bits)
|
|
What is route poisoning?
|
When a subnet is unreachable, it will broadcast an update with an infinite metric to advertise that the subnet is unreachable
|
|
What port type/number does RIPv1 & v2 use?
|
UDP 520
|
|
I can't configure a VLAN on my switch in a VTP domain, what could be a common cause?
|
The VTP mode for the switch is most probably configured with 'vtp mode client'
|
|
How do I delete the VTP information for a switch?
|
VTP information is stored in the 'vlan.dat' file. Deleting this would be the answer.
|
|
How can I stop routing updates on a specific interface?
|
(config-router)#passive-interface f0/1
|
|
What port states in STP are classed as 'Stable'?
|
Blocking, Discarding and Forwarding
|
|
Why does Rapid-STP have better a quicker convergence than PVST+?
|
Listening and Learning states are not in Rapid-STP. This gets rid of the 15 + 15 seconds delay....
|
|
On a root port switch, what role would all ports be?
|
All ports will be Designated (Desg) ports
|
|
In an STP topology, will a switch port in the listening state store an incoming ethernet frames source MAC address?
|
No, listening state doesn't store or even forward ethernet frames.
|
|
In STP, what is the link cost of a gigabit connection?
|
4
|
|
What are the OSPF multicast addresses?
|
224.0.0.5 and 224.0.0.6
|
|
How many areas would you expect a Backbone router to connect to?
|
A clue in the question, Backbone area is area 0. A Backbone Router would also be an Internal router (inside a single area)
|
|
What is commonly the first step when configuring MLPPP (Multilink PPP)
|
(config)#interface multilink 1
|
|
What is the default MaxAge for BPDU?
|
20 seconds
|
|
conf-reg value in ROMMON mode to bypass the startup-configuration when resetting a password?
|
0x2142
|
|
What port does TACAS+ use?
|
TCP 49
|
|
What is the RFC that defines RADIUS?
|
RFC 2865
|
|
3 tables that OSPF manage
|
Neighbor, LSDB (Link state database) and Routing table
|
|
What is the Cisco 'alternative' to PPP?
|
HDLC
|
|
What Fiber standard can I use for 10Gbps with a distance around 40KM?
|
10GBASE-ER
|
|
MetroEthernet Topology name for Point-To-Point connection?
|
Ethernet Line Service
|
|
Which RFC defines IPSec?
|
RFC 4301
|
|
What is an alternative to IPSec that can be used via the clients web browser?
|
SSL
|
|
What RFC defines GRE?
|
RFC 2784
|
|
What keyword can be used in an extended access-list for DNS traffic?
|
domain
|
|
What command would you use to apply an access list on the vty lines?
|
access-class [number] [in | out]
|
|
What will happen when a router has a higher priority in HSRP and the '#standby preempt' command is issued.
|
That specific router will take over as the active router.
|
|
Can 2 rotuers configured with HSRP run different versions?
|
No, they need to be configured with the same version to work
|