General Technician Chapter 14

Front 1

When is a mechanic responsible for checking A.D. compliances?

Back 1

When performing an inspection required under part 91, 125, or 135

Front 2

Check thrust bearing nuts for tightness on new or newly overhauled engines at the first inspections following installation.

Back 2

150 hours

Front 3

Aviation maintenance alerts

Back 3

Provide information about aircraft problems and suggest corrective action.

Front 4

The -100 in the title block applicable to which doubler part number?

Back 4

-101

Front 5

What regulations are covered by 14 CFR part 1

Back 5

Definitions and abbreviations

Front 6

A complete detailed inspection and adjustment of a valve mechanism will be made at the first 25 hours after the engine has been placed in service. At what interval will valve mechanism inspection be performed?

Back 6

100 hours

Front 7

What is the maximum penalty for cheating or other unauthorized conduct when taking a FAA mechanic test?

Back 7

Ineligibility to receive any certificate or rating for one year, and suspension or revocation of any certificate held

Front 8

How long are A. D. Compliance records required to be kept?

Back 8

They shall be retained, and then transferred with the aircraft when it is sold.

Front 9

Which regulation provides the airworthiness standards for an airplane certification in the normal category?

Back 9

14 CFR part 23

Front 10

What does the type certificate data sheet designation code 2 P.C.S.M. mean?

Back 10

2 place,

Closed,

Sea,

Monoplane,

Front 11

A TSO Is used by whom?

Back 11

The administrator

Front 12

An aircraft type certificate data sheet contains

Back 12

Location of Datum

Front 13

Which regulation provides information regarding instrument range markings for an airplane certified in the normal category?

Back 13

14 CFR part 23

Front 14

1. Manufacturers data and FFA publications such as airworthiness directives, type certificate data sheets.....

2. FAA publications such as technical standard orders, airworthiness directives...

Back 14

Only Number two is true

Front 15

Suitability for use of specific propellers with a particular engine-airplane combination can be determined by reference to what informational source?

Back 15

Aircraft specification or aircraft type certificate data sheet

Front 16

The following words are an example of what part of statement in an A. D.?

Back 16

Compliance

Front 17

Specifications pertaining to an aircraft model manufactured under a type certificate, of which less than 50 are shown on the FAA aircraft registry, can be found in the

Back 17

Aircraft listing

Front 18

1. A supplemental type certificate may be issued two more than one applicant for the same design change....

2. In installation of an item manufactured in accordance with the technical standard order system requires no further approval....

Back 18

Only number one is true

Front 19

How many parts will need to be fabricated by the mechanic in the construction and installation of 1 doubler?

Back 19

3

Front 20

1. Propellers are not included in the airworthiness directive.

2. A certified PowerPlant mechanic may make and minor repair on an aluminum propeller....

Back 20

Only number two is true

Front 21

An aircraft mechanic is privileged to perform major alterations on US certified aircraft. Which is not approved data?

Back 21

AC 43.13 - 2A

Front 22

Technical information about older aircraft models, of which no more than 50 remain in service, can be found in the

Back 22

Aircraft listing

Front 23

Using only the information given.... which doubler is it possible to construct and install?

Back 23

-101

Front 24

Airworthiness directives are issued primarily to

Back 24

Correct an unsafe condition

Front 25

Where are technical descriptions of certified propellers found?

Back 25

Propeller type certificate data sheets

Front 26

Which of the following includes all the regulatory descriptions of maintenance?

Back 26

Overhaul, repair, replace parts, preservation, inspection, and preventive maintenance

Front 27

The following is a table of are speed limits as given in A FAA issued aircraft specifications

Back 27

139 knots

Front 28

Type certificate data sheets are issued for which of the following products?

Back 28

Aircraft, engines, and propellers

Front 29

Primary responsibility for compliance with airworthy directives lies with the

Back 29

Aircraft owner and operator

Front 30

When an airworthy aircraft is sold, the airworthiness certificate

Back 30

Is transferred with the aircraft

Front 31

1. The FAA requires approval after compliance with the data of a supplemental type certificate.

2. an installation of an item manufactured in accordance with the technical standard order system requires no further approval

Back 31

Only number one is true

Front 32

What does the acronym TSO mean?

Back 32

Technical standard order

Front 33

The air transport association of America specification number 100....

1. Establishes a standard for the presentation of technical data and maintenance manuals.

2. Divides the aircraft into numbered systems and subsystems.

Back 33

Both number one and number two are true

Front 34

Which of the following are sometimes used as authorization to deviate from an aircraft original type design?

Back 34

1. FAA form 337

2. Supplemental type certificate

3. Airworthiness directive

Front 35

Placards required on an aircraft are specified in

Back 35

Aircraft specifications or type certificate data sheets

Front 36

under the Federal aviation regulations, and aviation maintenance technician is required to perform maintenance on an aircraft so that it

Back 36

Is at least equal to its original or priority altered condition.

Front 37

An aircraft has a total time in service of 468 hours. The airworthiness directive given was initially completed at 454 hours in service. How many additional hours in service maybe accomplished before the airworthiness directive must again be completed?

Back 37

186

Front 38

What information is generally contained in aircraft specifications or type certificate data sheets?

Back 38

Control surface movement

Front 39

Which doublers require heat treatment before installation

Back 39

-102

Front 40

The action required by an A.D. may take what form?

Back 40

1. Inspection

2. Part replacement

3. Design modification

And or

4. Change in Operating procedures

Front 41

What is the maintenance recording responsibility for the person who complies with an airworthiness directive?

Back 41

Make an entry in the maintenance records of that equipment

Front 42

The issuance of an Airworthiness Certificate is governed by

Back 42

14 CFR part 21