Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
97 Cards in this Set
- Front
- Back
|
What factor is not used in the operation of an aircraft gas turbine engine fuel control unit? A - compressor inlet air temperature B - mixture control position C - power lever position |
B - mixture control position |
|
|
In order to stabilize cams, springs, and linkages within the fuel control, manufacturers generally recommend that all final turbine engine trim adjustments be made in the A - increase direction B - decrease direction C - decrease direction after over-adjustment |
A - increase direction |
|
|
When trimming a turbine engine, the fuel control is adjusted to A - produce as much power as the engine is capable of producing B - set idle RPM and maximum speed or EPR C - allow the engine to produce maximum RRPM without regard to power output |
B - set idle RPM and maximum speed or EPR |
|
|
A supervisory electronic engine control (EEC) is a system that receives engine operating information and A - adjust a standard hydromechanical fuel control unit t obtain the most effective engine operation B - develops the commands to various actuators to control engine parameters C - controls engine operation according to ambient temperature, pressure, and humidity |
A - adjust a standard hydromechanical fuel control unit t obtain the most effective engine operation |
|
|
A full-authority electronic engine control (EEC) is a system that receives all the necessary data for engine operation and A - adjusts a standard hydromechanical fuel control unit to obtain the most effective engine operation B - develops the commands to various actuators to control engine parameters C - controls engine operation according to ambient temperature, pressure, and humidity |
B - develops the commands to various actuators to control engine parameters |
|
|
In a supervisory EEC system, any fault in the EEC that adversely affects engine operation A - causes redundant or backup units to take over and continue normal operation B - usually degrades performance to the extent that continue operation can cause damage to the engine C - causes an immediate reversion to control by the hydromechanical fuel control unit |
C - causes an immediate reversion to control by the hydromechanical fuel control unit |
|
|
The active clearance control (ACC) portion of an EEC system aids turbine engine efficiency by A - adjusting stator vane position according to operating conditions and power requirements B - ensuring turbine blade to engine case clearances are kept to a minimum by controlling case temperatures C - automatically adjusting engine speed to maintain a desired EPR |
B - ensuring turbine blade to engine case clearances are kept to a minimum by controlling case temperatures |
|
|
What should be checked/changed to ensure the validity of a turbine engine performance check if an alternate fuel is to be used? A - fuel specific gravity setting B - maximum RPM adjustment C - EPR gauge calibration |
A - fuel specific gravity setting |
|
|
The generally acceptable way to obtain accurate on-site temperature prior to performing engine trimming is to A - call the control tower to obtain field the temperature B - observe the reading on the aircraft Outside Air Temperature (OAT) gauge C - hang a thermometer in the shade of the nose wheel-well until the temperature reading stabilizes |
C - hang a thermometer in the shade of the nose wheel-well until the temperature reading stabilizes |
|
|
An aircraft should be facing into the wind when trimming an engine, However, if the velocity of the wind blowing into the intake is excessive, it is likely to cause a A - false low exhaust gas temperature reading B - trim setting resulting in engine overspeed C - false high compression and turbine discharge pressure, and a subsequent low trim |
C - false high compression and turbine discharge pressure, and a subsequent low trim |
|
|
A reciprocating engine automatic mixture control responds to changes in air density caused by changes in A - altitude or humidity B - altitude only C - altitude or temperature |
C - altitude or temperature |
|
|
On a float-type carburetor, the purpose of the economizer valve is to A - provide extra fuel for sudden acceleration of the engine B - maintain the leanest mixture possible during cruising best power C - provide a richer mixture and cooling at maximum power output |
C - provide a richer mixture and cooling at maximum power output |
|
|
The fuel metering force of a conventional float-type carburetor in its normal operating range is the difference between the pressure acting on the discharge nozzle located within the venturi and the pressure A - acting on the fuel in the float chamber B - of the fuel as it enters the carburetor C - of the air as it enters the venturi (impact pressure) |
A - acting on the fuel in the float chamber |
|
|
If the main air bleed of a float-type carburetor becomes clogged, the engine will run A - lean at rated power B - rich at rated power C - rich at idling |
B - rich at rated power |
|
|
Which method is commonly used to adjust the level of a float in a float-type carburetor? A - lengthening or shortening the float shaft B - add or remove shims under the needle-valve seat C - change the angle of the float arm pivot |
B - add or remove shims under the needle-valve seat |
|
|
What is the possible cause of an engine running rich at full throttle if it is equipped with a float-type carburetor? A - float level too low B - clogged main air bleed C - clogged atmospheric vent |
B - clogged main air bleed |
|
|
One of the things a metering orifice in a main air bleed helps to accomplish (at a given altitude) in a carburetor is A - pressure in the float chamber to increase as airflow through the carburetor increases B - a progressively richer mixture as airflow through the carburetor increases C - better fuel vaporization and control of fuel discharge, especially at lower engine speeds |
C - better fuel vaporization and control of fuel discharge, especially at lower engine speeds |
|
|
A punctured float in a float-type carburetor will cause the fuel level to A - lower, and enrich the mixture B - rise, and enrich the mixture C - rise, and lean the mixture |
B - rise, and enrich the mixture |
|
|
The back-suction mixture control system operates by A - varying the pressure within the venturi section B - varying the pressure acting on the fuel in the float chamber C - changing the effective cross-sectional area of the main metering orifice (jet) |
B - varying the pressure acting on the fuel in the float chamber |
|
|
If an aircraft engine is equipped with a carburetor that is not compensated for altitude and temperature variations, the fuel/air mixture will become A - leaner as either the altitude or temperature increases B - richer as the altitude increases and leaner as the temperature increases C - richer as either the altitude or temperature increases |
C - richer as either the altitude or temperature increases |
|
|
Float-type carburetors which are equipped with economizers are normally set for A - their richest mixture delivery and leaned by means of the economizer system B - the economizer system to supplement the main system supply at all engine speeds above idling C - their leanest practical mixture delivery at cruising speeds and enriched by means of the economizer system at higher power settings |
C - their leanest practical mixture delivery at cruising speeds and enriched by means of the economizer system at higher power settings |
|
|
If a float-type carburetor becomes flooded, the condition is most likely cause by A - a leaking needle valve and seat assembly B - the accelerating pump shaft being stuck C - a clogged back-suction line |
A - a leaking needle valve and seat assembly |
|
|
If an engine is equipped with a float-type carburetor and the engine runs excessively rich at full throttle, a possible cause of the trouble is a clogged A - main air bleed B - back-suction line C - atmospheric vent line |
A - main air bleed |
|
|
What occurs when a back-suction type mixture control is placed in IDLE CUTOFF? A - the fuel passages to the main and idle jet will be closed by a valve B - the float chamber will be vented to a negative pressure area C - the fuel passage to the idle jet will be closed by a valve |
B - the float chamber will be vented to a negative pressure area |
|
|
Which of the following best describes the function of an altitude mixture control? A - regulates the richness of the fuel/air charge entering the engine B - regulates the air pressure above the fuel in the float chamber C - regulates the air pressure in the venturi |
A - regulates the richness of the fuel/air charge entering the engine |
|
|
Select the correct statement concerning the idle system of a conventional float-type carburetor. A - the low-pressure area created in the throat of the venturi pulls the fuel from the idle passage B - climatic conditions have very little effect on idle mixture requirements C - the low pressure between the edges of the throttle valve and the throttle body pulls the fuel from the idle passage |
C - the low pressure between the edges of the throttle valve and the throttle body pulls the fuel from the idle passage |
|
|
On an engine equipped with a pressure-type-carburetor, fuel supply in the idling range is ensured by the inclusion in the carburetor of A - a spring in the unmetered fuel chamber to supplement the action of normal metering forces B - an idle metering jet that bypasses the carburetor in the idle range C - a separate boost venturi that is sensitive to the reduced airflow at start and idle speeds |
A - a spring in the unmetered fuel chamber to supplement the action of normal metering forces |
|
|
The economizer system of a float-type carburetor performs which of the following functions? A - it supplies and regulates the fuel required for all engine speeds B - it supplies and regulates the additional fuel required for all engine speeds above cruising C - it regulates the fuel required for all engine speeds and all altitudes |
B - it supplies and regulates the additional fuel required for all engine speeds above cruising |
|
|
How will the mixture of an engine be affected if the bellows of the automatic mixture control (AMC) in a pressure carburetor ruptures while the engine is operating at altitude? A - it will become leaner B - no change will occur until the altitude changes C - it will become richer |
C - it will become richer |
|
|
The fuel level within the float chamber of a properly adjusted float-type carburetor will be A - slightly higher than the discharge nozzle outlet B - slightly lower than the discharge nozzle outlet C - at the same level as the discharge nozzle outlet |
B - slightly lower than the discharge nozzle outlet |
|
|
The metered fuel pressure (chamber C) in an injection-type carburetor A - is held constant throughout the entire engine operating range B - varies according to the position of the poppet valve located between chamber D (unmetered fuel) and chamber E (engine-driven fuel pump pressure) C - will be approximately equal to the pressure in chamber A (impact pressure) |
A - is held constant throughout the entire engine operating range |
|
|
Select the statement which is correct relating to a fuel level check of a float-type carburetor. A - use 5 pounds fuel pressure for the test if the carburetor is to be used in a gravity fuel feed system B - block off the main and idle jets to prevent a continuous flow of fuel through the jets C - do not measure the level at the edge of the float chamber |
C - do not measure the level at the edge of the float chamber |
|
|
What carburetor component measures the amount of air delivered to the engine? A - economizer valve B - automatic mixture control C - venturi |
C - venturi |
|
|
If a float-type carburetor leaks fuel when the engine is stopped, a likely cause is that the A - float needle valve is worn or otherwise not seated properly B - float level is adjusted too low C - main air bleed is clogged |
A - float needle valve is worn or otherwise not seated properly |
|
|
Fuel is discharged for idling speeds on a float-type carburetor A - from the idle discharge nozzle B - in the venturi C - through the idle discharge air bleed |
A - from the idle discharge nozzle |
|
|
When air passes through the venturi of a carburetor, what three changes occur? A - velocity increases, temperature increases, and pressure decreases B - velocity decreases, temperature increases, and pressure increases C - velocity increases, temperature decreases, and pressure decreases |
C - velocity increases, temperature decreases, and pressure decreases |
|
|
Where is the throttle valve located on a float-type carburetor? A - between the venturi and the discharge nozzle B - after the main discharge nozzle and venturi C - after the venturi and just before the main discharge nozzle |
B - after the main discharge nozzle and venturi |
|
|
An aircraft carburetor is equipped with a mixture control in order to prevent the mixture from becoming too A - lean at high altitudes B - rich at high altitudes C - rich at high speeds |
B - rich at high altitudes |
|
|
Which of the following is NOT a function of the carburetor venturi? A - proportions the fuel/air mixture B - regulates the idle system C - limits the airflow at full throttle |
B - regulates the idle system |
|
|
Idle cutoff is accomplished on a carburetor equipped with a back-suction mixture control by A - intro ducting low pressure (intake manifold) air into the float chamber B - turning the fuel selector valve to OFF C - the positive closing of a needle and seat |
A - intro ducting low pressure (intake manifold) air into the float chamber |
|
|
One purpose of an air bleed in a float-type carburetor is to A - increase fuel flow at altitude B - meter air to adjust the mixture C - decrease fuel density and destroy surface tension |
C - decrease fuel density and destroy surface tension |
|
|
To determine the float level in a float-type carburetor, a measurement is usually made from the tope of the fuel in the float chamber to the A - parting surface of the carburetor B - top of the float C - centerline of the main discharge nozzle |
A - parting surface of the carburetor |
|
|
The throttle valve of float-type aircraft carburetors is located A - ahead of the venturi and main discharge nozzle B - after the main discharge nozzle and ahead of the venturi C - between the venturi and the engine |
C - between the venturi and the engine |
|
|
Why must a float-type carburetor supply a rich mixture during idle? A - engine operation at idle results in higher than normal volumetric efficiency B - because at idling speeds the engine may not have enough airflow around the cylinders to provide proper cooling C - because of reduced mechanical efficiency during idle |
B - because at idling speeds the engine may not have enough airflow around the cylinders to provide proper cooling |
|
|
What component is used to ensure fuel delivery during periods of rapid engine acceleration? A - acceleration pump B - water injection pump C - power enrichment unit |
A - acceleration pump |
|
|
The device that controls the ratio of the fuel/air mixture to the cylinders is called a A - throttle valve B - mixture control C - metering jet |
B - mixture control |
|
|
The device that controls the volume of the fuel/air mixture to the cylinders is called a A - mixture control B - metering jet C - throttle valve |
C - throttle valve |
|
|
Which statement is correct regarding a continuos-flow fuel injection system used on many reciprocating engines? A - fuel is injected directly into each cylinder B - fuel is injected at each cylinder intake port C - two injector nozzles are used in the injector fuel system for various speeds |
B - fuel is injected at each cylinder intake port |
|
|
During the operation of an aircraft engine, the pressure drop in the carburetor venturi depends primarily upon the A - air temperature B - barometric pressure C - air velocity |
C - air velocity |
|
|
Which of the following causes a single diaphragm accelerator pump to discharge fuel? A - an increase in venturi suction when the throttle valve is open B - an increase in manifold pressure that occurs when the throttle valve is opened C - a decrease in manifold pressure that occurs when the throttle valve is opened |
B - an increase in manifold pressure that occurs when the throttle valve is opened |
|
|
At what engine speed does the main metering jet actually function as a metering jet in a float-type carburetor? A - All RPM's B - cruising RPM only C - all RPM's above idle range |
C - all RPM's above idle range |
|
|
An aircraft engine continuous cylinder fuel injection system normally discharges fuel during which stroke(s)? A - intake B - intake and compression C - all (continuously) |
C - all (continuously) |
|
|
What is the purpose of the carburetor accelerating system? A - supply and regulate the fuel required for engine speeds above idle B - temporarily enrich the mixture when the throttle is suddenly opened C - supply and regulate additional fuel required for engine speeds above cruising |
B - temporarily enrich the mixture when the throttle is suddenly opened |
|
|
When troubleshooting an engine for too rich a mixture to allow the engine to idle, what would be a possible cause? A - economizer valve not operating correctly B - mixture setting too rich C - air leak in the intake manifold |
A - economizer valve not operating correctly |
|
|
What is the relationship between the accelerating pump and the enrichment valve in a pressure injection carburetor? A - no relationship since they operate independently B - unmetered fuel pressure affects both units C - the accelerating pump actuates the enrichment valve |
A - no relationship since they operate independently |
|
|
What is the relationship between the pressure existing within the throat of a venturi and the velocity of the air passing through the venturi? A - there is no direct relationship between the pressure and the velocity B - the pressure is directly proportional to the velocity C - the pressure is inversely proportional to the velocity |
C - the pressure is inversely proportional to the velocity |
|
|
Which of the following is least limey to occur during operating of an engine equipped with a direct cylinder fuel injection system? A - afterfiring B - kickback during start C - backfiring |
C - backfiring |
|
|
What carburetor component actually limits the desired maximum airflow to the engine at full throttle? A - throttle valve B - venturi C - manifold intake |
B - venturi |
|
|
On a carburetor without an automatic mixture control as you ascend to altitude, the mixture will A - be enriched B - be leaned C - not be affected |
A - be enriched |
|
|
During engine operation, if carburetor heat is applied, it will A - increase fuel/air ratio B - increase engine RPM C - decrease the air density to the carburetor |
C - decrease the air density to the carburetor |
|
|
The desired engine idle speed and mixture setting A - is adjusted with engine warmed up and operating B - should give minimum RPM with maximum manifold pressure C - is usually adjusted in the following sequence; speed first, then mixture |
A - is adjusted with engine warmed up and operating |
|
|
A nine-cylinder radial engine, using a multiple-point priming system with a central spider, will prime which cylinders? A - one, two, three, eight, and nine B - all cylinders C - one, three, five, and seven |
A - one, two, three, eight, and nine |
|
|
What is a function of the idling air bleed in a float-type carburetor? A - it provides a means for adjusting the mixture at idle speeds B - it vaporizes the fuel at idling speeds C - it aids in emulsifying/vaporizing the fuel at idle speeds |
C - it aids in emulsifying/vaporizing the fuel at idle speeds |
|
|
If the volume of air passing through a carburetor venturi is reduced, the pressure at the venturi throat will A - decrease B - be equal to the pressure at the venturi outlet C - increase |
C - increase |
|
|
(Refer to FIgure 6.) Which curve most nearly represents an aircraft engine's fuel/air ratio throughout its operating range? A - 1 B - 3 C - 2 |
C - 2 |
|
|
What will occur if the vapor vent float in a pressure carburetor loses its buoyancy? A - the amount of del returning to the fuel tank from the carburetor will be increased B - the engine will continue to run after the mixture control is placed in IDLE CUTOFF C - a rich mixture will occur at all engine speeds |
A - the amount of del returning to the fuel tank from the carburetor will be increased |
|
|
What method is ordinarily used to make idle speed adjustments on a float-type carburetor? A - an adjustable throttle stop of linkage B - an orifice and adjustable tapered needle C - an adjustable needle in the drilled passageway which connects the airspace of the float chamber and the carburetor venturi |
A - an adjustable throttle stop of linkage |
|
|
For what primary purpose is a turbine engine fuel control unit trimmed? A - to obtain maximum thrust output when desired B - to properly position the power levers C - to adjust the idle RPM |
A - to obtain maximum thrust output when desired |
|
|
Which type of fuel control is used on most of today's turbine engines? A - eletromechanical B - mechanical C - hydromechanical or electronic |
C - hydromechanical or electronic |
|
|
Under which of the following conditions will the trimming of a turbine engine be most accurate? A - high wind and high moisture B - high moisture and low wind C - no wind and low moisture |
|
|
|
(1) The mixture used at rated power in air cooled reciprocating engines is richer than the mixture used through the normal cruising range. (2) The mixture used at idle in air cooled reciprocating engines is richer than the mixture used at rated power. Regarding the above statements, A - only No. 1 is true B - only No. 2 is true C - both No. 1 and No. 2 are true |
C - both No. 1 and No. 2 are true |
|
|
Under which of the following conditions would an engine run lean even though there is a normal amount of fuel present? A - the use of too high an octane rating fuel B - incomplete fuel vaporization C - the carburetor air heater valve in the HOT position |
B - incomplete fuel vaporization |
|
|
During idle mixture adjustments, which of the following is normally observed to determine when the correct mixture has been activated? A - changes in fuel/air pressure ratio B - fuel flowmeter C - changes in RPM or manifold pressure |
C - changes in RPM or manifold pressure |
|
|
An indication that the optimum idle mixture has been obtained occurs when the mixture control is moved to IDLE CUTOFF and manifold pressure A - decreases momentarily and RPM drops slightly before the engine ceases to fire B - increases momentarily and RPM drops slightly before the engine ceases to fire C - decreases and RPM increases momentarily before the engine ceases to fire |
C - decreases and RPM increases momentarily before the engine ceases to fire |
|
|
The use of less than normal throttle opening during starting will cause A - a rich mixture B - a lean mixture C - backfire due to lean fuel/air ratio |
A - a rich mixture |
|
|
When checking the idle mixture on a carburetor, the engine should be idling normally, then pull the mixture control toward the IDLE CUTOFF position. A correct idling mixture will be indicated by A - a immediate decrease in RPM B - a decrease of 20 to 30 RPM before quitting C - an incase of 10 to 50 RPM before decreasing |
C - an incase of 10 to 50 RPM before decreasing |
|
|
When a new carburetor is installed on an engine, A - warm up the engine and adjust the float level B - do not adjust the idle mixture setting; this was accomplished on the flow bench C - and the engine is warmed up to normal temperatures, adjust the idle mixture, then the idle speed |
C - and the engine is warmed up to normal temperatures, adjust the idle mixture, then the idle speed |
|
|
The purpose of the back-suction mixture control in a float-type carburetor is to adjust the mixture by A - regulating the pressure drop and the venturi B - regulating the pressure on the fuel in the float chamber C - regulating the suction on the mixture from behind the throttle valve |
B - regulating the pressure on the fuel in the float chamber |
|
|
Reciprocating engine power will be decreased at all altitudes if the A - air density is increased B - humidity is increased C - manifold pressure is increased |
B - humidity is increased |
|
|
If the idling jet becomes clogged in a float-type carburetor, the A - engine operation will not be affected at any RPM B - engine will not idle C - idle mixture becomes richer |
B - engine will not idle |
|
|
An aircraft engine equipped with a pressure-type carburetor is started with the A - primer while the mixture control is positioned at IDLE CUTOFF B - mixture control in the FULL-RICH position C - primer while the mixture control is positioned at the FULL-LEAN position |
A - primer while the mixture control is positioned at IDLE CUTOFF |
|
|
One of the best ways to increase engine power and control detonation and preignition is to A - enrich the fuel/air mixture B - use water injection C - lean the fuel/air mixture |
B - use water injection |
|
|
An excessively lean fuel/air mixture may cause A - an increase in cylinder head temperature B - high oil pressure C - backfiring through the exhaust |
A - an increase in cylinder head temperature |
|
|
The density of air is very important when mixing fuel and air to obtain a correct fuel-to-air ratio. Which of the following weighs the most? A - 75 parts of dry air and 25 parts of water vapor B - 100 parts of dry air C - 50 parts of dry air and 50 parts of water vapor |
B - 100 parts of dry air |
|
|
A mixture ratio of 11:1 normally refers to A - a stoichiometric mixture B - 1 part air to 11 parts fuel C - 1 part fuel to 11 parts air |
C - 1 part fuel to 11 parts air |
|
|
The economizer system in a float-type carburetor A - keeps the fuel/air ratio constant B - functions only at cruise and idle speeds C - increases the fuel/air ratio at high power settings |
C - increases the fuel/air ratio at high power settings |
|
|
A carburetor is prevented from eating out during quick acceleration by he A - power enrichment system B - mixture control system C - accelerating system |
C - accelerating system |
|
|
In turbine engines that utilize a pressurization and dump valve, the dump portion of the valve A - cuts off fuel flow to the engine fuel manifold and dumps the manifold fuel into the combust or to burn just before the engine shuts down B - drains the engine manifold lines to prevent fuel boiling and subsequent deposits in the lines as a result of residual engine heat (at engine shutdown) C - dumps extra fuel into the engine in order to provide for quick engine acceleration during rapid throttle advancement |
B - drains the engine manifold lines to prevent fuel boiling and subsequent deposits in the lines as a result of residual engine heat (at engine shutdown) |
|
|
What effect does high atmospheric humidity have on the operation of a jet engine? A - decreases engine pressure ratio B - decreases compressor and turbine RPM C - has little or no effect |
C - has little or no effect |
|
|
What are the positions of the pressurization valve and the dump valve in a jet engine fuel system when the engine is shut down? A - pressurization valve closed, dump valve open B - pressurization valve open, dump valve open C - pressurization valve closed, dump valve closed |
A - pressurization valve closed, dump valve open |
|
|
What could cause a lean mixture and high cylinder head temperature at sea level or low altitudes? A - mixture control valve fully closed B - defective accelerating system C - automatic mixture control stuck in the extended position |
C - automatic mixture control stuck in the extended position |
|
|
Which of the following is NOT an input parameter for a turbine engine fuel control unit? A - compressor inlet pressure B - compressor inlet temperature C - ambient humidity |
C - ambient humidity |
|
|
detonation occurs when the fuel/air mixture A - burns too fast B - ignites before the time of normal ignition C - is too rich |
A - burns too fast |
|
|
What corrective action should be taken when a carburetor is found to be leaking fuel from the discharge nozzle? A - replace the needle valve and seat B - raise the float level C - turn the fuel off each time the aircraft is parked |
A - replace the needle valve and seat |
|
|
A major difference between the Teledyne-Continental and RSA (Precision Airmotive or Bendix) continuous flow fuel injection systems in fuel metering is that the A - RSA system uses air pressure only as a metering force B - Continental system utilizes airflow as a metering force C - Continental system uses fuel pressure only as a metering force |
C - Continental system uses fuel pressure only as a metering force |
|
|
The function of the altitude compensating, or aneroid valve used with the Teledyne-Continental fuel injection system on many turbocharged engines is to A - prevent an overly rich mixture during sudden acceleration B - prevent detonation at high altitudes C - provide a means of enriching the mixture during sudden acceleration |
A - prevent an overly rich mixture during sudden acceleration |
|
|
The primary purpose of the air bleed openings used with continuous flow fuel injector nozzles is to A - provide for automatic mixture control B - lean out the mixture C - aid in proper fuel vaporization |
C - aid in proper fuel vaporization |
