Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
54 Cards in this Set
- Front
- Back
Rpm fluctuations at any power setting |
+/- 1 |
|
What percentage does the emer gen come online |
14-18% |
|
What percent can you advance the throttle? |
20% |
|
At or above what percent is steady state motoring achieved |
23% |
|
What percent does the start pump cutout switch disengage? |
50-54% |
|
What percent does the main generator come online |
56-58 |
|
What is the rpm minimum at idle to minimize bearing compartment oil leakage? |
66% (above 65%) |
|
What percent to clear display Flo lo light or when mpd or MPCD goes blank |
73% |
|
What percent for 2 minutes to clear unstable idle(twice only) |
75% |
|
What percent must canopy be closed and locked |
80% |
|
What is the max rpm percent? |
94% |
|
How much can your FTIT fluctuate at any power setting? |
+/-10 |
|
What is your max degrees at idle in primary mode |
575 |
|
What is your max at idle in secondary mode? |
650 |
|
What is the max temp on start? |
680 |
|
At what degrees or above for 1 minute requires a 5 minute cool down at idle? |
700 |
|
What degrees max in primary mode when operating at mil or above ? |
970 |
|
What is the degree max in secondary power mode when operating at mil or above? |
1012 |
|
What is maximum oil fluctuation at idle? |
+/- 5 |
|
What is the maximum oil fluctuation at or above mil? |
+/-10 psi |
|
What is the psi on start- not to exceed 1 minute of operation? |
0 psi |
|
What is the rise of oil for minimum of 20 seconds when transitioning throttle from idle - mil? |
15psi for 20 seconds |
|
What is the normal oil pressure from idle - mil power? |
20-80psi |
|
What is the normal psi at mil power and above? |
30-80psi |
|
What is the minimum oil pressure at idle when fluctuating? |
15psi |
|
What is the minimum oil pressure at mil? |
30psi |
|
What is the maximum pressure on start for the first minute only? |
100psi |
|
What is the nozzle position at idle? |
70-95% |
|
What is the nozzle position at mil? |
30% or less |
|
What is the nozzle position at max? |
60-80% |
|
What is the nozzle position in sec mode? |
5% or less |
|
How long for JFS acceleration on finger lift? |
5 seconds |
|
What is the maximum time for green ready light to come on when temperature is above 0 F? |
10 seconds |
|
What is the time for the green ready light if it is 0 F or below? |
15 seconds |
|
How many seconds must pass between JFS engagements? |
20 seconds |
|
How many seconds must pass between JFS attempts? |
30 seconds |
|
How many seconds for light off indication? |
30 seconds |
|
How many seconds for engine to stabilize at idle? |
40 seconds |
|
How long must you motor for restarts after 30 minutes but less than 3.5 hours? |
40 seconds |
|
How many seconds must you be at idle before cycling eng control switch if eng control light displayed? |
90 seconds |
|
How many seconds must you be at idle before cycling eng control switch if eng control light displayed on start? |
90 seconds |
|
How many seconds is a normal JFS engagement time operation? |
90 seconds |
|
What is the max during emergency JFS engagement time operation? |
150 seconds |
|
How many minutes for oil indication after light off? (min 0,max 100psi) |
1 |
|
How many minutes for FTIT to stabilize at idle on start? |
2 minutes |
|
How many minutes can you be at max power? |
3 minutes |
|
What is the minimum time for an engine run? |
5 minutes |
|
How many minutes must pass after priming JFS? |
10 minutes |
|
How many minutes must pass after priming hot JFS? |
30 minutes |
|
How many minutes can you be at mil power? |
30 minutes |
|
What is pc1 hydraulic limits? |
2750-3250 |
|
What is pc2 hydraulic limits? |
2750 - 3250 |
|
What is utility hydraulic limits with the right motor started? |
2550-3000 |
|
What is utility hydraulic pressure with the left engine or both started? |
2750 - 3250 |