Dental Instruments Test

Front 1

Back 1

Cone socket mouth mirror-used for visual examination, reflection of light, and to retract tissues.

Front 2

Back 2

Simple Stem mouth mirror- used for visual examination, reflection of light, and to retract tissues.

Front 3

Back 3

Perio probe- used to measure the depth of the gingival sulcus during the patient's oral exam.

Front 4

Back 4

Discoid Spoon Excavator- used to remove soft decay from dentin of prep.

Front 5

Back 5

Spoon Escavator- used to remove soft decay from the dentin in the prep..

Front 6

Back 6

Enamel Hatchet- used to plane enamel on buccal and lingual axial walls on Class II preps.

Front 7

Back 7

Off-Angled Hatchet- used to plane enamel on the buccal and lingual axial walls on Class II preps.

Front 8

Back 8

Straight Chisel- used to plane enamel on the labial and lingual axial walls of Class III and IV preps.

Front 9

Back 9

Wedelstaedt Chisel- used to plane enamel on the lingual axial walls on Class III and IV preps.

Front 10

Back 10

Mesial Margin Trimmer- used to plane the mesial gingival margin on Class II inlay & onlay preps.

Front 11

Back 11

Distal Margin Trimmer- used to plane the distal gingival margin on Class II Inlay & Onlay preps.

Front 12

Back 12

Hoe, anterior- used to plane pupal floor of Class III and IV preps.

Front 13

Back 13

Special Hoe, Posterior- used to plane the pupal floor of Class I and II preps in an amalgam procedure.

Front 14

Back 14

Amalgam condenser- used to pack and condense amalgam or cement into a prepared cavity preparation.

Front 15

Back 15

Discoid-cleoid carver- used to carve amalgam on the occlusal surfaces of the posterior teeth.

Front 16

Back 16

Hollenback Carver- used to carve interproximal surfaces of restoration.

Front 17

Back 17

Interproximal Carver- used to carve the interproximal surfaces of the amalgam restoration.

Front 18

Back 18

Frahm's Carver- used to carve occlusal surfaces of amalgam restorations on posterior teeth.

Front 19

Back 19

Wall's carver- used to carve the occlusal surface of amalgam restorations on posterior teeth

Front 20

Back 20

Egg/Ball Burnisher- is used to burnish or smooth the margins of metallic restorations.

Front 21

Back 21

Ball Burnisher- is used to burnish or smooth the margins of metallic restorations.

Front 22

Back 22

Beavertail burnisher- used to burnish or smooth the margins of metallic restorations.

Front 23

Back 23

Articulating paper holder- Used to hold articulating paper to check occlusal surfaces.

Front 24

Back 24

Tofflemire retainer- holds the matrix band snugly in position.

Front 25

Back 25

Universal Matrix Band- thin flexible steel band. Used in tofflemire retainer.

Front 26

Back 26

Gingival retraction instrument- used to pack gingival retraction cord during crown prep or gold prep procedure.

Front 27

Back 27

PFI instrument- convey and pack dental cements & composite into prepared cavity prep.

Front 28

Back 28

Plastic composite instrument- used to convey & pack composite materials into prepared cavity preps.

Front 29

Back 29

Flexible spatula- used to mix various dental cements and materials.

Front 30

Back 30

Wax Spatula- used to carry hot wax to prepared tooth.

Front 31

Back 31

Wax carver- used to carve wax patterns in prepared teeth.`

Front 32

Back 32

Jacquette scaler- used to remove hard deposits of calculus and stain from surface of tooth by hand.

Front 33

Back 33

Sickle scaler- used to remove hard deposits of calculus from surface of tooth by hand.

Front 34

Back 34

Curette- remove hard deposits from the surface of the tooth by hand.

Front 35

Back 35

Crown & Bridge Scissors

Front 36

Back 36

Crown & Bridge remover- used to remove a crown or bridge after it has been seated with permanent cement, such as zinc phosphate.

Front 37

Back 37

Prop- used to assist the mouth in remaining open.

Front 38

Back 38

Gag- used to assist the mouth in remaining open

Front 39

Back 39

Dappen dish- hold pastes & liquid during a packing in carrier.

Front 40

Back 40

Amalgam well- used to hold the amalgam.

Front 41

Back 41

Svedopter- used to isolate the area prior to seating a crown on mandibular arch.

Front 42

Back 42

Cotton roll holder- used to hold cotton rolls in place on mandibular arch.

Front 43

Back 43

Composite syringe- used to extrude the composite resin into a cavity prep.

Front 44

Back 44

Boley Gauge- used to measure in millimeters.

Front 45

Back 45

Scalloping scissors- used to trim vinyl &

Front 46

Back 46

Crimping Pliers- used to crimp the edges of a temporary crown to reduce circumference.

Front 47

Back 47

Belling Pliers- used to bend the edges of a temporary crown.

Front 48

Back 48

Contouring Pliers- used to contour or roll the edges of a temporary crown.

Front 49

Back 49

Dental Dam Punch- used to create holes in the dental dam.

Front 50

Back 50

Rubber Dam Forceps- used to place and remove dental dam clamp.

Front 51

Back 51

Young frame- holds the dam in place during procedure.