Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
75 Cards in this Set
- Front
- Back
|
Positions of the SCP & PCP |
PCP Inboard, SCP Outboard |
|
|
How can PFD be displayed on MFD #2 |
Failure of MFD #1 or PFD |
|
|
From Main format how is Cruise format displayed? |
Pressing Mode button on SCP |
|
|
What displays are avalible via SYS button on SCP? |
Electical, Hydraulic, EPAC |
|
|
What screens can display the DMG in full page format? |
MFD #1 |
|
|
What describes the function of the ALL button on SCP? |
Cycles; Main, Cruise and Video |
|
|
The DMG is initially displayed very dim, how do you make it brighter? |
Contrast rocker |
|
|
What SCP buttons/knobs are used exclusively in the MFD Maintenance Screen? |
SEL knob, ENT |
|
|
What does the amber WCD flag indicate? |
A discrepancy between the two VMM's CAS outputs. |
|
|
What is the horn above the pilots head for? |
Rotor Low |
|
|
RCP knob names |
AHRS, VMM, PCP, ADC, ENG DATA |
|
|
What is the main function of the PCP |
Manages parameters of the PFD |
|
|
What is the purpose of the CAL button on SCP? |
To enable calibration of pressure sensors. |
|
|
What magic box carries out calibration of the pressure sensors? |
VMM |
|
|
How do you change between Main and Cruise format? |
MODE button on PCP |
|
|
What CDS source discrepancy warnings are there? |
IAS, PITCH, ROLL, HDG, ALT, VNE |
|
|
When the ENG DATA switch on the RCP's selected to ANA 1 or ANA 2, which engine parameters are lost on MFD 2 for the selected engine? |
ITT & Torque (answer not in book # dealwithitHamish) |
|
|
Where is ANA 1 data sent from the engine? |
VMM 1 |
|
|
Which control panel is used to display / select bearing pointers on the PFD |
PCP |
|
|
From which display format is calibration mode entered? |
MAIN |
|
|
What is the priority of sensors for hover mode? |
GPS, Doppler, AHRS |
|
|
Where does the Electronic standby Instrument (ESBI) receive its air data from? |
Via #1 side pitot / static pipelines |
|
|
What does the static alternate source selector do? |
Bypasses the static input from #2 pitot head. |
|
|
What source discrepancy errors can be indicated from AHRS? |
PITCH, ROLL, HDG |
|
|
What indication is expected for a Radar Altimeter failure? |
#2 RA FAIL |
|
|
What reference system is inactive in the ground? |
Doppler |
|
|
How many units make up the Doppler velocity system? |
1 |
|
|
Where is ADU 1 located? |
Nose avionics bay LHS |
|
|
Where is ADU 2 located? |
Cockpit side of nose to cockpit bulkhead RHS |
|
|
What antennas are connected to the VOR 1 and 2 receivers? |
VOR localiser x2, Glideslope and Marker Beacon |
|
|
Where is the Marker Beacon antenna located, |
Fuselage underside, Inboard of RH MLG bay. |
|
|
How is DME frequency tuned? |
Automatically based in VOR freq selection. |
|
|
Which controls are used to display ADF info on the HSI? |
BRG #1 & 2 |
|
|
What purpose does the MCDU scratchpad area preform? |
All of the above (system messages and data entry) |
|
|
What are the two navigation (FMS) position fixing modes? |
GPS and Best Computed Position |
|
|
Which system sends a blanking pulse to the DME? |
IFF |
|
|
Which system sends a blanking pulse to the ADF? |
HF |
|
|
What are the 2 cards for the ADL? |
Blue (R/W maint data) & Red (R/O comms plan / nav data) |
|
|
What does GPS 0.02 indicate on the top right of MCDU FMS page? |
GPS providing position info with estimated error of 0.02nm |
|
|
Which system is displayed on the APD during duplex autopilot operation with APD button depressed? |
APD #1 |
|
|
What AFCS function is lost after an autopilot failure leading to simplex operation? |
Auto-trim |
|
|
What autopilot functions remain after an AP MISCOMP has occurred? |
AP 1 & 2 only |
|
|
How do the AFCS Servos actuators operate in Duplex mode? |
Controlled by respective FCMs and preform 50% of the work each. |
|
|
What happens to series actuators associated with a failed FCM/AP? |
Actuator is commanded to return to neutral. |
|
|
What happens to the yaw series actuator in the event of a number one hydraulic system failure. |
Both actuator ends re-center and the actuator ceases to function. |
|
|
What happens when the autopilot is decoupled from the Automatic Flight Director? |
The pilots must manually fly the aircraft, following steering cues on the PFD. |
|
|
What type of tone is transmitted on 121.5 and 243Mhz? |
Swept tone |
|
|
What distress freq signal contains identification and last known position information? |
406.025 Mhz |
|
|
How do you silence the ELT in event of accidental activation? |
Switch to rest and hold until ELT transmission ceases (call tower as well) |
|
|
In maintenance mode loading screen, which option is used to carry out the post-flight download from VMM1? |
VMM1 HUMS LD |
|
|
Which systems feed the Electronic Standby Instrument? |
Air data from the #1 system pitot/static system, AHRS 1, VOR 2 |
|
|
Where does the DMG get its flight plan information from? |
NAVM |
|
|
Which MFD can display the DMG in full-page format? |
MFD1 |
|
|
How long does the CVDR record for after power is applied and the engines are not started and WOW switches have not been set to flight? |
10 minutes |
|
|
Where is the collective parallel actuator located? |
On the transmission work deck. |
|
|
How long can the Cockpit Voice Recorder record audio for before it starts overwriting itself? |
2 Hours |
|
|
Where is the AP DISC push-button located?
|
The cyclic grips |
|
|
What does the V/UHF 3 Guard module do? |
Provides digital and trunked communications (in UHF) |
|
|
Where is the KY-100 Remote Control Module located? |
Cockpit, rear interset console |
|
|
Where is the KY-100 Main Terminal located? |
Aft Avionics bay |
|
|
What must the KY-100 Main Terminal Unit be set to, to permit access from the cockpit controls? |
PT & REM |
|
|
What type of audio is routed through the red audio resister box? |
Secure comms only |
|
|
What type of audio is routed through the black audio resister box? |
Plain comms only |
|
|
Who can hear all the Aural Warning Generation (AWG) system messages? |
Pilot and Co-pilot |
|
|
What HF modulation setting is required for SELCAL to be used? |
AM |
|
|
How is the SELCAL light extinguished if it illuminates? |
Selecting CALL AK from the HF SETTINGS page |
|
|
Which radio has an integrated data port in the cabin? |
V/UHF 2 |
|
|
What is the purpose of the DAGR GPS? |
Provides timing for V/UHF 1 & 2 freq hopping comms |
|
|
What commonly causes engine/transmission noise to break through on the ICS? |
GCP VOX setting to low |
|
|
What RMS systems remain when CMU is failed? |
All NAV receivers, V/UHF 2, HF, and pilot / co-pilot ICS
|
|
|
Which LRU(s) send barometric altitude data to the IFF transponder for IFF Mode C? |
CMU |
|
|
What are the 3 ND display modes for the PFD? |
HSI, FPLN, Hover |
|
|
BRG button cycle order |
OFF, VOR, ADF, FMS (Page 90) |
|
|
What does the CHECK PFD flag indicate? |
Discrepancy between two comparing displays |
|
|
What does the VMM do? |
Concentrates system data and sends to the display units. |
