Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
46 Cards in this Set
- Front
- Back
Which type of clutch discs would best suit a linehaul truck with a high torque rise engine? |
Dampened disc with ceramic facings |
|
After completing a TMC wheel end adjustment which of the following confirms that the adjustment is as specified? |
End play of 0.001-inch to 0.005-inch measured with a dial indicator. |
|
Which of the following statements about truck wheel ends is true? |
A tire is mounted to a rim, and the rim is mounted to a wheel. |
|
Technician A says that bursting of clutch friction facings is often caused by coasting a truck with the clutch pedal depressed. Technician B says that a clutch pressure plate with warpage sufficient to insert a 0.005 inch thickness gauge under a straight edge must be replaced. Who is correct? |
Both A and B. |
|
Technician A says that one advantage of a clutch brake is its ability to bring a vehicle to a halt at low speeds. Technician B says that improper use of a clutch brake when bringing a vehicle to a halt can destroy it. Who is correct? |
Technician B only. |
|
When installing a clutch pack assembly, at what point should you knock out the wood chocks that hold off pressure plate spring pressure? |
When pressure plate is bolted tight to the flywheel. |
|
Where is a clutch (bell) housing flange face most susceptible to wear at its mating surface with the flywheel housing? |
Between 3 and 8 o'clock |
|
What is recommended advice for selecting the appropriate starting gear? |
Select a gear ratio that allows you to start moving with the engine at idle rpm. |
|
When the Urge-to-move feature is used on an Eaton Autoshift, what hardware component in the system makes this possible? |
wet clutch |
|
When using the ATA Technical and Maintenance council method of setting truck wheel ends, what is the first step torque setting usually specified as? |
200 lb-ft |
|
Which of the following are advantages of truck disc wheels when compared with cast spoke wheels? |
Fewer alignment problems, extends tire life, and lighter weight. |
|
What is the function of coaxial springs in a clutch friction plate? |
Dampening of driveline torsionals, reducing clutch chatter, dampening of engine torsionals. |
|
What should 1 1/2 to 2 inches of clutch free pedal produce in free travel between the clutch release yoke fingers and the release bearing in a push type clutch? |
1/8 inch |
|
What method should be used to adjust wheel bearings on all non-unitized wheel hubs? |
TMC method |
|
When you use a clutch installation pilot shaft to align a clutch for installation, which set of splines must be aligned? |
Clutch friction plate splines |
|
Which of the following would most likely result if the intermediate plate drive pins in a pot type flywheel housing are not properly aligned? |
Clutch hangs-up on release. |
|
Which of the following clutch pack components never rotates? |
Release bearing housing |
|
What is required at PMI to maintain a Solo clutch through its service life? |
Check wear indicator and lube release bearing. |
|
Clutch facing wear has resulted in zero clutch pedal free travel in a truck equipped with a manually adjustable, pull-type clutch. Which of the following is the recommended method of restoring clutch pedal free travel to specification? |
Move the internal adjusting ring 6 to 8 notches clockwise. |
|
Which of the following clutch pack components has to always rotate at the same speed as the engine flywheel? |
Pressure plate |
|
As clutch friction facings wear on a truck pull-type clutch, how is clutch pedal free travel affected? |
Decreases. |
|
Which of the following procedures is BEST practice for removing a bearing race from an aluminum hub? |
Preheat the hub in a thermostatically controlled oven and tap out with a steel drift. |
|
When mounting a set of duals to a cast spoke wheel, where should the spacer ring be placed? |
Between the inboard and outboard tires. |
|
Which of the following dimensions is within the specified clutch pedal freeplay dimension measured at the pedal? |
1 3/4 inches |
|
Which type of clutch pressure plate design provides a constant plate load as the friction faces wear? |
Angle spring, pull-type and diaphragm spring, pull-type clutch. |
|
Where should the clutch pedal be positioned while the internal adjusting ring of a pull-type clutch is being turned during a clutch adjustment? |
Fully depressed. |
|
What is generally considered to be the major cause of clutch failure? |
Excess heat. |
|
Which of the following correctly describes how most truck wheel bearings are lubricated? |
Wet (oil bath) hub |
|
What tools should be used to install a typical truck wheel seal? |
Seal driver and hammer. |
|
What is the function of the rollers used on some clutch release forks (yokes)? |
Extended fork life. |
|
Which of the following dimensions is regarded as being correct for clutch brake squeeze at the clutch pedal? |
1 inch |
|
Technician A says that clutch shaft pilot bearings should be replaced each time a clutch pack is replaced. Technician B says that the pilot bearing should always be inspected when a clutch pack is replaced. Who is correct? |
Technician A only. |
|
Which of the following components can easily be modified for use as a pilot shaft for installing clutch assemblies? |
Transmission input shaft |
|
Technician A says that a Solo clutch should automatically adjust for the life of the clutch pack. Technician B says that any clutch using a lockstrap to set the adjusting ring, must be periodically adjusted. Who is correct? |
Both A and B. |
|
Technician A says that the wheel bearing on a unitized hub system does not require adjustment during the life of the hub. Technician B says that periodic topping up of oil in wheel hubs is eliminated in some types of unitized axle. Who is correct? |
Both A and B. |
|
Which of the following heavy truck wheel types would be best suited to a harsh, construction site environment? |
Cast spoke |
|
Which of the following is a major advantage of a cast spoke wheel compared with a stud-piloted disc wheel? |
Fewer wheel-off incidents |
|
Which of the following is the drive side of a clutch pack assembly? |
Flywheel, intermediate plate, and clutch cover. |
|
What is the function of the clutch brake? |
Enables shifting into first and reverse. |
|
Which of the following driving practices can cause abnormal wear to clutch components? |
Standing starts in high gear ratios, riding the clutch pedal and using the clutch to hold a truck on an incline. |
|
When installing a 15 1/2 inch clutch assembly, technician A uses guide studs installed in the flywheel to support the weight. Technician B uses a splined pilot shaft when installing both 14 and 15 1/2 inch clutch assemblies. Who is correct? |
Both A and B. |
|
Which side of a truck equipped with stud-piloted disc wheels has left-hand thread lug nuts? |
Left. |
|
Technician A says that in most cases when an external clutch adjustment is required, it is the result of a prior improper clutch adjustment. Technician B says that to adjust clutch free pedal travel, you should begin by adjusting the external linkage. Who is correct? |
Neither A or B. |
|
Technician A says that disc wheels nuts and studs on the left side of a truck often use a right hand thread. Technician B says that disc wheels often use fasteners that unscrew in the reverse of their direction of forward rotation. Who is correct? |
Technician B only. |
|
Technician A says that when a clutch brake is damaged by driver abuse, the transmission must be removed to install a replacement clutch brake. Technician B says that a two-piece clutch brake can be used as a replacement for an integral brake. Who is correct? |
Technician B only. |
|
What could cause clutch hang-up? |
Misaligned intermediate plate drive pins. |