Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
51 Cards in this Set
- Front
- Back
What kind of nitrogen is used on the NAN Cart? |
Oil free, type 1 class 1 grade B |
|
How pure must the nitrogen be on the NAN Cart? |
99.5 percent |
|
What controls the flow from the manifold assembly to the boost pump preset regulator? |
Pump motor valve |
|
What range is the booster air drive pressure gauge? |
0-200 psi |
|
What indicates nitrogen/air pressure at the motor inlet? |
Booster air drive pressure gauge. |
|
What type of gauge assembly is used with the NAN Cart? |
Type A Class 4 MIL DTL 8348 |
|
What preoperational checklist manual is used to perform a preoperational inspection on the nitrogen cart? |
AG-750AO-MRC-100 |
|
What controls the flow of nitrogen from the manifold assembly to the suction side of the pump section? |
Booster pump inlet valve |
|
What gauges indicates pressure of nitrogen in the service hose for servicing high pressure? |
High pressure outlet gauge |
|
What range is the high pressure outlet gauge? |
0-5000 PSI and 500-3500 for aircraft |
|
What range are the pressure cylinder gauges? |
0-5000 |
|
What components separates cylinder 1 and 2 from cylinders 3-6? |
Manifold bypass valve |
|
What indicates nitrogen pressure at the inlet of the regulator manifold assembly? |
Regulator inlet pressure gauge |
|
What range is the regulator inlet pressure gauge? |
0-5000 PSIG |
|
What range is the low pressure inlet gauge? |
0-600 and 0-500 for aircraft system |
|
What controls the flow of nitrogen from the manifold assembly to the regulator manifold assembly inlet? |
Manifold shut-off valve |
|
What regulates the amount of pressure from the regulator manifold assembly to the service hose in pounds per square inch? |
Service hose control regulator |
|
What direction must you turn the regulator to decrease pressure? |
Counterclockwise |
|
What direction must you turn the service hose valve to open? |
Counterclockwise |
|
What kind of nitrogen on the NAN Cart charged with? |
Oil free |
|
What type of nitrogen is used on the NAN Cart? |
Type 1 class 1 grade B |
|
You should not use cylinders with pressure less than what PSI? |
500 |
|
When servicing is to be done in the range of 0-500 PSIG what gauge must you observe? |
Low pressure outlet gauge |
|
When servicing is to be done in the range of 500-3500 PSIG what gauge must you observe? |
High pressure outlet gauge |
|
The pump will automatically stop when pressure reaches what PSI? |
3500 |
|
What must pump drive pressure be at to obtain 3500 PSI when using booster air drive? |
117 |
|
What is the Part number for the inflator kit assembly? |
M85352/1 |
|
In which direction must the lapped surface of the shear seal face so that it will interface with the lapped surface of the rotor? |
Towards the top of the selector valve |
|
What is used to lubricate the ball bearings on the NAN Cart? |
MIL-PRD-10924 |
|
When performing pre intallation testing, how much pressure must you apply to the selector valve? |
30PSIG |
|
What type of anti seize tape should you apply to the selector valve before installing it? |
A-A-58092 |
|
How much PSI must be applied to cylinder 1 when performing proof pressure testing? |
6000 PSI |
|
How much PSI must be applied to cylinder 2 when performing proof pressure testing? |
6000 PSI |
|
How much PSI should the cylinder indicates during return when performing proof pressure testing? |
1000 psi |
|
When performing leakage testing, how much pressure must be applied to the pressure port? |
4000 psi |
|
Leakage at the port shall not exceed what value when performing leakage testing? |
2 S C I M |
|
When performing a bench test how much pressure should be applied to the inlet side of the regulator? |
3500 psi |
|
What should the outlet pressure be set at during bench testing? |
117 psi |
|
How many times should the relief valve be tested on the NAN cart? |
2 |
|
At what pressure should the relief valve relieve at? |
3750 psi |
|
What range is the booster air drive pressure gauge |
0 to 200 PSI |
|
What indicates nitrogen/air pressure at the motor inlet |
Booster air drive pressure gauge |
|
What controls the flow from the manifold assembly to the boost pump preset regulator |
Pump motor valve |
|
How pure is nitrogen used on the NAN cart |
99.5 percent |
|
NAVOSH program manual for forces afloat |
OPNAV INSTRUCTIONS 5100.19 |
|
Policies, procedures, & responsibilities for assignment and application of uniform source, maintenance, and Recoverability (SM&R) code |
4423.29 |
|
Navy occupational safety &health (NAVOSH) program manual |
OPNAV INSTRUCTIONS 5100.23 |
|
What is GAPL? |
Group assembly parts list. Uses a six column format. All symbols and abbreviation are In accordance with ASMEY14.38M |
|
ADRL |
Automatic distribution requirement list |
|
How can you request for additional publication |
Have to submit a Milstrip requisition in accordance with NAVSUP INSTRUCTION 458 to routing identifier code NFZ |
|
What size is the modification plate has to be |
4 inches by 2 inches |