Reading...
Play button
Play button
Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
140 Cards in this Set
- Front
- Back
|
ADIRU alignment must not be attempted at latitudes greater than?
|
78 Deg 15 Minutes
|
|
|
Icing Conditions
|
10 deg C or 50 deg F
|
|
|
Fuel IMBAL for Taxi/Takeoff or Landing
|
1,000 lbs
|
|
|
Fuel System Min and Max Temperature
|
-43 C (or FFP +3) and 49 C
|
|
|
Alternate flap duty cycle
|
1-5 is 5 minutes
>15 is 25 minutes |
|
|
Minimum Altitude for speed brake use?
|
1,000 feet AGL
|
|
|
Max Flap Extension Altitude?
|
20,000 feet
|
|
|
Engine ignition must be ON for
|
Takeoff, Landing, Heavy Rain, and Anti-Ice
|
|
|
Caution Limits are what color?
|
Amber
|
|
|
Minimum Engine limits are what color?
|
Red
|
|
|
Maximum Engine limits are what color?
|
Red
|
|
|
Min Alt for A/P ON during Non-Pre App?
|
50 feet below minimums
|
|
|
Min alt for A/P ON after Takeoff?
|
400 ft
|
|
|
APU Electrical Only?
|
41,000
|
|
|
APU Bleed Only?
|
17,000
|
|
|
APU Bleed and Electrical?
|
10,000
|
|
|
Max Cabin Diff Psi
|
9.1
|
|
|
Max Zero Fuel Weight?
|
136,000
|
|
|
Max Landing Weight?
|
144,000
|
|
|
Max Takeoff Weight?
|
174,200
|
|
|
Max Ramp Weight?
|
174,700
|
|
|
Max Takeoff and Landing Alt
|
8,400
|
|
|
Max Alt
|
41,000
|
|
|
Turb A/S
|
280/.78
|
|
|
Max Speed
|
320/.82
|
|
|
Max Tailwind and Crosswind
|
15/36 (winglets 33)
|
|
|
Runway Slope
|
+/- 2%
|
|
|
What is the purpose of the STAB TRIM OVERRIDE switch? is this function electrical or manual?
|
Bypasses the control column actuated stab trim cutout switches (under floor) to restore power to the stabilizer trim switches. Electrical function
|
|
|
Can the rudder be trimmed with a loss of hydraulics?
|
NO
|
|
|
Where is the rudder trim indicated?
|
Aft pedestal indicator
|
|
|
Does the rudder have trim tabs?
|
NO
|
|
|
Can the Autopilot trim the rudder?
|
NO
|
|
|
Do the pedals move when the rudder is trimmed?
|
YES
|
|
|
How is the rudder trim accomplished?
|
Through the rudder feel and centering unit
|
|
|
How is the aileron trim accomplished?
|
Electrically through Aileron feel and control unit
|
|
|
Do the ailerons move when they are trimmed?
|
YES
|
|
|
Can the autopilot trim the Ailerons?
|
NO
|
|
|
Can you trim the ailerons with the autopilot engaged?
|
Yes, but you should not due the limits
|
|
|
Where is aileron trim indicated
|
Top of Yoke
|
|
|
Which NAV modes will display TCAS traffic?
|
Map, center map, VOR or APP modes
|
|
|
What does a Traffic Alert look like?
|
Solid Amber circle
|
|
|
What does a RA look like?
|
Solid Red Square
|
|
|
What does pitch guidance on the PFD look like?
|
Restrictive red bands
|
|
|
What does vertical speed guidance on the IVSI look like?
|
Red-do not fly to
Green fly to |
|
|
IN the TA/RA mode, when is the RA inhibited?
|
Stall
Wind shear, GPWS < 1,000 |
|
|
What is the purpose of the Test button?
|
When activated it test the radar system operation without transmitting
|
|
|
What does the WX button do?
|
Show weather radar returns at the selected gain level
|
|
|
What about the WX-T button?
|
Also shows turbulence within 40 miles
|
|
|
What is the power source for Fire Detection?
|
Battery Bus
|
|
|
What is the power source for fire protection?
|
Hot battery bus
|
|
|
What is the power source for wheel well fir detection?
|
#1 AC transfer bus
|
|
|
What happens when you pull an engine fire handle?
|
Closes 4 - Bleed, Hyd, Eng Fuel, and Spar Fuel valves
Disables 2 - Rvrsrs, Engine hyd low press light Arms 1 - FE Squib Trips 1 - GCR&B Allows 1 - Rotation of Fire switch |
|
|
Where are the engine fire bottles located?
|
Wheel well
|
|
|
What are the indications of an APU fire?
|
Fire warning bell sounds
Both Fire warning lights illuminate APU fire warning switch illuminates APU automatically shuts down Wheel well fire warning horn sounds (on ground only) and wheel well light flashes |
|
|
Where is the APU fire bottle located?
|
At the APU compartment
|
|
|
What happens when you pull the APU fire handle?
|
Closes 3 - Fuel SOV & S, Bleed, Air inlet door
Arms 1 - FE Squib Trips - GCR and B Allows - Rotation of APU Fire switch Provide backup to auto shutdown |
|
|
Stab trim cutout switches?
|
Disconnect stab trim during a runaway
|
|
|
Which of these switches will cause disengagement of the A/P if engaged
|
Stab trim A/P cutout
|
|
|
What does the Takeoff configuration system monitor?
|
PoTSSFuL
Parking Brake Trim Speed Brake Spoilers Flaps LEDs |
|
|
Can you cancel the takeoff configuration warning?
|
NO
|
|
|
When will you get a configuration warning?
|
ON the ground and either or both the Thrust Levers are advance for takeoff
|
|
|
Why are the gates positioned at the 1 and 15 degree setting?
|
Go-around flap settings
|
|
|
What do you have to do to get past the gates?
|
Push down and move it out
|
|
|
What are normal landing flap settings
|
30 and 40
|
|
|
When the flap handle is at 5 degrees, where are the LEDs
|
LEFs full extend
LESs extend |
|
|
When the flap handle is at 15 degrees, where are the LEDs
|
LEFs and LESs full extend
|
|
|
Does the flap handle move during auto slat operation?
|
No
|
|
|
Does the flap handle move during flap blowup operation
|
No
|
|
|
Should the flap lever be moved during alternate flap operation?
|
Yes, as called for in the checklist
|
|
|
What does pressing this (Horn cutout) button accomplish?
|
Silences the landing gear warning horn
|
|
|
Does it always cancel the configuration horn?
|
NO
|
|
|
Why or when does the Horn cutout button not always cancel the configuration horn?
|
Flaps are 15 or greater with Landing Gear Up
|
|
|
How many auto throttle actuators are there?
|
One servo motor for each throttle (2)
|
|
|
What has to happen before revers thrust can be selected?
|
Throttles must be at idle position
|
|
|
Can the throttles be advanced while in reverse thrust?
|
No
|
|
|
What light might you see on the forward panel if there is a fault in the parking brake system?
|
Anti-skid inop light
|
|
|
What is the significance of the green band on the Stab Trim Wheel trim scale?
|
Allowable range for takeoff
|
|
|
Does the speed brake lever have to be armed to get the spoilers on an RTO? Why?
|
NO, During RTO auto speed brake system works when: Wheel Spin up (60 knots), reverse thrust is selected
|
|
|
Does the speed brake lever have to be armed to get the spoilers on Landing?
|
Yes
|
|
|
When does the speed brake system operate on landing?
|
Armed (light on), both throttles to idle, flight spoilers deploy, RA <10, flight spoilers on any gear compression, ground spoilers deploy on right main strut compresses, wheel spin up (60)
|
|
|
In flight what is controlled by the speed brake lever?
|
Flight spoilers (symmetrically)
|
|
|
What is the caution concerning the use of the speed brake lever in flight?
|
Be careful in a turn and sever buffet past flight detent
|
|
|
When would the Below G/S light illuminate?
|
Eccessive Glide Slope deviation (1.3 DOT)
|
|
|
When can you inhibit the below G/S light
|
Below 1,000 radalt
|
|
|
Which hydraulic system is used for alternate nose wheel steering?
|
System B
|
|
|
Is alternate nose wheel steering ever automatically selected?
|
No
|
|
|
In the normal mode, which hydraulic system is providing power for NW steering?
|
System A
|
|
|
In the alternate mode, which hydraulic system is providing power for NW steering?
|
System B
|
|
|
What are the three windows of the Flight Mode Annunciator (FMA)?
|
Auto throttle, roll, pitch
|
|
|
How would you move the Captains or FO's outboard or inboard display to another location?
|
Display select panel switch
|
|
|
Which windows to the air vent controls defrost?
|
1 Left and Right
|
|
|
What is indicated by the illumination of the SPEED BRAKES EXTENDED light on the FO's panel?
|
In flight: beyond armed and TE flaps >10, or RA <800'
Ground: Lever in down detent and ground spoilers deployed |
|
|
What is normal brake pressure?
|
3,000 psi
|
|
|
What is the maximum brake pressure?
|
3,500 psi
|
|
|
What is the normal pre-charge brake accumulator pressure?
|
1,000 psi
|
|
|
Which system pressurizes the brake accumulator?
|
System B
|
|
|
With the accumulator only, what braking is available?
|
Several applications and parking brake
|
|
|
What is indicated by a red gear light?
|
Landing gear is Not down and locked, throttles idle and less than 800 feet Radalt or disagreement with lever (in-transit or unsafe)
|
|
|
What is indicated by 2 green landing gear lights on FO's panel and 3 green landing gear lights on overhead panel?
|
Gear is down and locked
|
|
|
What is indicated by all lights extinguished?
|
Gear is UP and Locked
|
|
|
What is the OFF position of the Landing Gear Lever used for
|
Removes hydraulic pressure from landing gear system
|
|
|
What is the trigger on the Landing Gear Handle for?
|
Allows the landing gear to be raised, bypassing the lever lock.
|
|
|
What normally release the landing gear handle lever lock?
|
Air/Ground Sensing
|
|
|
When the gear handle is raised on takeoff, what takes place
|
Hydraulic Pressure releases up-locks, brakes stop tire rotation, retraction is accomplished, mechanical up-locks engage to hold gear up.
|
|
|
When the gear handle is moved to the down position what happens?
|
HYD press releases up locks
Gear extends by HYD press, air loads, and gravity Overcenter mechanical and HYD locks hold the gear at full extension |
|
|
What causes the LE FLAPS EXT green light to illuminate?
|
All LEDS extended (full ext with 10 thru 40)
|
|
|
What other indication, besides the LE FLAPS EXT light to confirm or determine the position of the LED's
|
LED annunciator panel
|
|
|
What does the Illumination of the LE FLAPS TRANSIT amber light indicate?
|
Any LED in transit
Any LED not in programmed position Slat skew or asymmetry (inboard 3 only) During alternate flap extension until reaching TE flaps 10 |
|
|
Will the LE FLAPS TRANSIT amber light illuminate during autoslat extension?
|
NO
|
|
|
What can be determined from the TE flap position indicator?
|
Flap Position, Asymmetry or Skew
|
|
|
What electrical power is need for the Flap position indicator?
|
28 volts AC (Transfer Bus # 2)
|
|
|
How would you be able to determine an asymmetry condition in the flaps?
|
Split Needle on Indicator
|
|
|
Do alternate brakes have anti-skid?
|
Yes
|
|
|
What is different about anti-skid protection with alternate brakes?
|
Paired Wheels
|
|
|
What kind of protection is available with normal brakes?
|
Individual Wheel Brakes
|
|
|
If the ANTI SKID light is ON, does anti skid work?
|
NO
|
|
|
What types of Anti-skid are available?
|
(SLTH)
Skid Locked wheel Touchdown Hydroplane |
|
|
What does an illuminated ANTI-SKID light indicated?
|
A system fault exists
|
|
|
How can the pilot disarm the auto brake system
|
Move selector to off
Speed brake lever to the down detent advancing a throttle momentarily Manual braking |
|
|
Will auto brakes operate with alternate brake system?
|
No
|
|
|
What does RTO refer to?
|
Rejected takeoff mode
|
|
|
When do you get auto brakes during RTO?
|
Throttles above idle above 90 knots
|
|
|
What happens if you reject the takeoff below 90 knots?
|
No auto brakes are activated and RTO remains armed
|
|
|
What condition must exist in order to arm RTO?
|
On Ground
Anti skid and auto brakes operational Less than 60 knots Idle power Switch on |
|
|
What happens to the RTO mode once airborne?
|
Automatically Disarmed
|
|
|
What happens to the switch when RTO is automatically disarmed?
|
It does not move
|
|
|
What happens if you land and the RTO mode switch is still selected
|
No autobrake action occurs
|
|
|
What happens when you first select an autbrake mode for landing?
|
self test
|
|
|
what indications do you get when the autobrake system has successfully completed its self test
|
None
|
|
|
What indications do you get if the auto brake system does not successfully complete its self test
|
amber AUTO BRAKE DISARM light
|
|
|
How many level of deceleration can be selected with the auto brakes ?
|
4
|
|
|
What kind of braking do you get in the MAX mode?
|
less than produced by Full pedal braking
|
|
|
What is different about selecting MAX auto brake?
|
You must pull the switch out and rotate
|
|
|
After landing, when does auto brake application begin?
|
Both thrust levers to idle and main wheel spin up
|
|
|
Can landing auto brake selections be made after landing
|
Yes
|
|
|
When can you select after landing?
|
Any time above 60 knots
|
|
|
Will the auto brake system completely stop the airplane?
|
Yes
|
|
|
When does the amber AUTO BRAKE DISARM light illuminate?
|
Speed brake lever moved to down detent during RTO or landing
Manual Brakes applied during landing Thrust levers advanced or.... Landing (3 second rule) landing made with RTO selected |
|
|
How long will the ISFD operate after the main battery has been depleted?
|
150 minutes
|
|
|
What does the Auto position of the Engine Display Control Panel switch Mean for N1 set and Speed Ref?
|
Both references bugs are set by FMC
|
