Reading...
Play button
Play button
Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
214 Cards in this Set
- Front
- Back
|
Who's responsible for detecting deficiencies on trailers?
|
The Vehicle Operator
|
|
|
When must hoist hooks be replaced?
|
15% in excess opening and more than 10 degree twist from plane
|
|
|
Turning radius of a 141 trailer
|
40 degrees or 200 inches
|
|
|
Top speed of the MJ-1 jammer
|
18 MPH
|
|
|
TO that provides guidance on loading conv/nuclear weapons on HCU-6/E aircraft pallets
|
11N-45-51B
|
|
|
TO about 141 trailers
|
35D3-2-27-1
|
|
|
TO about 110 trailers
|
35D3-2-26-1
|
|
|
The actual length of a 40-foot trailer
|
51 feet
|
|
|
Tester used to test circuits with AIM-9,7, and 120 missiles
|
AMTEC 620
|
|
|
Tester designed primarily for the testing of solid-fuel rocket motor igniter bridge wire circuitry
|
101-5BFG
|
|
|
Rollerized trailer is designer for what?
|
Handling cargo loaded on HCU-6/E aluminum aircraft pallets
|
|
|
Publication for guidance and safe lifting procedures for lifting devices
|
AFOSH 91-46
|
|
|
PSI for safe operation of pneumatic tools.
|
90 PSI
|
|
|
The multimeter we use
|
AN/PSM-37
|
|
|
Most common type of sling used
|
Wire rope
|
|
|
Most common size of electric saw blade
|
8 inches
|
|
|
Max load of 226 trailers
|
12,000 pounds
|
|
|
Max load of 110 trailers
|
15,000 pounds
|
|
|
Max capacity of MJ-1 with extension lift arms
|
2,200 pounds
|
|
|
Max capacity of an MHU-83 using fork adapter assembly
|
6,000 pounds
|
|
|
Max capacity of a pair of 110 trailer rail extenders
|
3,000 pounds
|
|
|
Lifting capacity of the MJ-1 jammer with the bomb rollers attached
|
3,000 pounds
|
|
|
How many storage boxes are on the 226 trailer?
|
5
|
|
|
How many openings are on the deck of the 226 trailer?
|
3
|
|
|
AN/PSM-37 max readable voltage
|
1000 volts (5000 w/ test prod)
|
|
|
AN/PSM-37 max readable resistance
|
100 megaohms
|
|
|
AN/PSM-37 max readable current
|
1 amp (10 with the shunt)
|
|
|
Adjustments you can make on the cradle/boom of the MHU-83
|
Tilt, Lateral, Longitudinal
|
|
|
Three types of trailers you are most likely to see
|
Van(closed), flatbed(open), rollerized
|
|
|
How do you protect the starter of a jammer during cold weather?
|
Don't depress for more than 20 seconds
|
|
|
When loading/unloading jammer, what should the directional control lever be in?
|
Neutral with parking brake set to prevent inadvertent movement.
|
|
|
Three uses of the MC-7 Compressor
|
power pneumatic tools, provide air for cleaning/drying equipment components, and provide air for vacu-blast operations.
|
|
|
Why should the MC-7 compressor be operated with the cover doors closed?
|
To prevent operator hearing loss.
|
|
|
Compressed air can cause injury at what minimum amount?
|
10 to 15 psi
|
|
|
What publication governs the use of PPE for an air compressor operator
|
AFOSH Standard 91-501
|
|
|
How is accidental connection of high/low-pressure systems prevented?
|
Non-interchangeable chucks and connectors.
|
|
|
How does the bobtail get its name?
|
The back end was shortened by about half
|
|
|
What is a unique feature of the pintle hook.
|
and can move in, out, or sideways to make coupling with a trailer easier.
|
|
|
What is the turning radius of the bobtail?
|
22 feet
|
|
|
What does paying attention to local weather conditions provide?
|
Maximizes use time, minimizes downtime.
|
|
|
What is operator maintenance?
|
Systematic care of a vehicle to include cleaning, servicing, and inspecting for discrepancies daily.
|
|
|
What alerts you that the air pressure in a X-ton truck is too low?
|
Warning buzzer, light, or both.
|
|
|
What type of driving are the high-range gears of the transmission used in a X-ton truck?
|
Normal
|
|
|
Why would you never race a cold engine?
|
The oil needs a chance to circulate through the engine
|
|
|
Who is responsible for the secure tie down of a load on a cargo truck?
|
The Vehicle Operator
|
|
|
What is the primary purpose of the MB-4 tug?
|
Towing aircraft
|
|
|
What is the towing capacity of the MB-4 tug?
|
140,000 pounds
|
|
|
If the MB-4 tug is operated on dry pavement with the differential lever in the LOCKED, what can happen?
|
Severe damage to the tractor drive train
|
|
|
What is a no-slip drive system?
|
Every wheel turns exactly the same as any other wheel
|
|
|
What is the first step in mating a tractor and trailer?
|
Place chocks between tractor wheels
|
|
|
What is the major concern while driving a tractor and trailer?
|
Be aware of the length of your trailer and make wide turns.
|
|
|
While backing a tractor and trailer...
|
Use just one spotter.
|
|
|
Primary purpose of the Johnson bar.
|
To slow the trailer to prevent jackknifing.
|
|
|
Nontactical forklifts are most effective where?
|
Pavement
|
|
|
What are the two types of tactical forklifts?
|
Rough and adverse terrain
|
|
|
What's the procedure for shutting down a rough-terrain forklift
|
release load and lower engine speed at the same time. Run engine at half speed for 4-5 minutes then close throttle. Set ignition switch to OFF
|
|
|
Name two special-purpose forklifts.
|
Variable-reach and swingmast
|
|
|
What are the forklift tine height requirements while traveling with a load?
|
tilted back and raised only as far as necessary to clear road surface
|
|
|
Why should you drive backwards with bulky loads?
|
For better vision
|
|
|
How far from combustible material must a forklift be parked?
|
10 feet
|
|
|
What is the most common type of container for general purpose, dry cargo?
|
ISO Containers
|
|
|
What is the weight capacity of the superstacker forklift?
|
50,000 pounds
|
|
|
What must you do before using the sideloader to lift or drop off an ISO container?
|
Ensure the trailer stabilizer legs are extended
|
|
|
Two types of munitions not transported on a 110 trailer
|
Nuclear and missiles
|
|
|
The parking brake on the 110 trailer affects how many wheels?
|
Four inboard rear wheels
|
|
|
How many trolley and chock assemblies are supplied with the 110 trailer?
|
20 trolleys and 40 chocks
|
|
|
Ensures the smooth transfer of HCU-6/E pallets from a rollerized trailer to an aircraft/K-loader.
|
An adjustable ramp
|
|
|
The moving of munitions from one base to another, depot to base, or base to depot is called
|
Logistical movement
|
|
|
Movement to support on-base operations to or from the flight line is called
|
Operational movement
|
|
|
Prior to any operation involving a van trailer, you MUST
|
Make sure automatic heating/refrigerating devices are inoperative
|
|
|
The purpose of the transport beam beneath the lift arm assemblies on the MJ-1 jammer is to...
|
Provide more support and to relieve excess hydraulic pressure from the arms in carrying loads long distances
|
|
|
When using MJ-1 jammer extension lift arms, you have immediately...
|
Reduced its lifting capacity by 800 pounds
|
|
|
What is the lifting capacity of the MHU-83 jammer?
|
7,000 pounds
|
|
|
When releasing the accelerator on a hydrostatic transmission vehicle...
|
it coasts to a stop very quickly
|
|
|
What are the minimum and maximum frame-width adjustments of the MHU-83?
|
70 inches to 140 inches
|
|
|
How do you adjust the yaw on the MHU-83
|
Hydraulically
|
|
|
The external power receeptacle for starting if the battery is dead is featured in only what jammer?
|
MHU-83 B/E
|
|
|
The purpose of the azimuth control on the MHU-83 jammer is that it allows for
|
Left and right movement of the boom assembly
|
|
|
What is the warm-up period for the glow plugs on diesel-engine-equipped lift truck?
|
30 to 60 seconds
|
|
|
What is the rated capacity of air per minute needed for the MC-7 air compressor to discharge 100 psi of pressure?
|
125 cubic feet
|
|
|
The MC-7 Air compressor is designed for what type of maintenance?
|
General maintenance
|
|
|
The diesel model of the MC-7 air compressor is capable of operating up to how long without refueling?
|
8 hours
|
|
|
What is the primary difference between a bobtail and a pickup?
|
The bobtail's back end was shortened by about one-half.
|
|
|
What is the maximum tow capacity of the bobtail towing support equipment?
|
40,000 pounds
|
|
|
The maximum towing speed of the bobtail while towing equipment is how fast?
|
15 mph
|
|
|
Do not energize the starter on a cargo truck for more than how long?
|
30 seconds
|
|
|
What should you do if the differential lever of the MB-4 tug is difficult to shift?
|
Drive forward or backward a short distance, stop, and attempt to shift the lever
|
|
|
Which position should the differential shift lever be in while driving the MB-4 tug on dry road surfaces?
|
Unlocked
|
|
|
While driving the MB-4 tug on adverse (slipper) road surfaces, in what position should the differential shift lever be?
|
Locked
|
|
|
To ensure proper mating when backing a tractor to mate with a trailer, the fifth wheel of the tractor must be in exact line with what?
|
The kingpin on the trailer
|
|
|
Which procedure is not required when demating a tractor and trailer?
|
Set the semitrailer hand-brake lever
|
|
|
Which forklift has the solid front axle and a pivot pin that allows the fron end to pivot when turning the steering wheel?
|
Adverse-terrain forklift
|
|
|
What is the maximum reach of the variable-reach forklift with the forks elevated at 45 degrees?
|
15 feet
|
|
|
What is the maximum speed limit of a forklift when operating around aircraft?
|
5 mph
|
|
|
When may unfuzed loaded weapons be transported on the tines of a forklift?
|
When the weapons body is strong enough to prevent damage and is long enough to be transported safely.
|
|
|
Which type of forklift has a dead-man switch that can be operated from the driving position?
|
Electric
|
|
|
When can you store powered equipment in a building with explosives?
|
Only in fire-resistive buildings and such equipment is essential to day-to-day operations.
|
|
|
When using a drill, the first thing to do is
|
Make sure the diameter of the hole to be drilled is within the capacity of the drill
|
|
|
An electric saw's blade must be operating at what speed before it contacts the material being cut?
|
Full speed
|
|
|
What is the maximum towing speed of the UALS?
|
20 mph
|
|
|
What technical order covers the UALS?
|
35D30-4-15-1
|
|
|
What is the purpose of the scoop disk of the inner drum?
|
Transfers rounds from the entrance cover assembly to the outer drum partitions to the exit cover assemblies.
|
|
|
What is the important safety measure to remember about the interface unit?
|
It has an exposed three-gear cluster that turns
|
|
|
How is the cranking initiated on the UALS?
|
half-inch speed wrench or pneumatic drive assembly inserted into the drive receptacle.
|
|
|
How is the replenisher operated?
|
Manually or pneumatically
|
|
|
Which technical order gives a full description of the replenisher?
|
35D30-4-11-1
|
|
|
Which subassembly of the replenisher supports and transports spent cases and unfired rounds from the loader to the replenisher?
|
Convery element belt
|
|
|
What is the function of the delinker loader
|
Strips links from the ammunition, then feeds the rounds into the replenisher.
|
|
|
Name two 30mm ammunition loading systems currently being used in the Air Force
|
GFU-7/e and the GFU-10/E
|
|
|
Which container is used to house the 30mm ammunition in lunk tube carriers?
|
CNU-309/E
|
|
|
What does the container interface tool provide?
|
Properly guides and layers the LTC in the containers
|
|
|
What assemblies comprise a complete GFU-10/E ALS?
|
Replenisher assy., transporter assy., loader assy., pod interface unit, and the rounds return unit
|
|
|
What trailer is capable of singularyly transporting an A/E32K-3 MAC?
|
The 110 trailer
|
|
|
About how large of a site is required for the MAC bomb buildup operation?
|
50' x 100'
|
|
|
Which TO contains specific information on the MAC?
|
35D2-17-1
|
|
|
What is used to route electrical and pneumatic power to the MAC?
|
The Interface Control Board (ICB)
|
|
|
Which piece of powered equipment can supply pneumatic power to the MAC?
|
The MC-7
|
|
|
What is used to level the gantries once the MAC is assembled?
|
The adjustment bar
|
|
|
What is the purpose of the restraint strap for the MAC?
|
It's used at a workstation to prevent the bomb body from turning while torque is applied
|
|
|
How many munitions items can be raised, moved, and lowered onto dollies for the MAC?
|
Up to three at a time
|
|
|
What happens once the dollies on the MAC are empty?
|
They're placed on the return rail for reuse.
|
|
|
Why is it important to monitor the NEW during your operations?
|
The instructions in 91-201 always apply to prevent propagation of an explosion from one location to another.
|
|
|
What should be the first thing disconnected during disassembly of the MAC?
|
The ICB (Interface Control Board)
|
|
|
Who can use flashing red lights while transporting explosives?
|
Security Forces unless prohibited by local laws
|
|
|
When may you push or pull munitions containers?
|
When the containers are designed with skids
|
|
|
If a munitions item or container of items is dropped, what must be done?
|
Verify the drop distance criteria to ensure the item is still serviceable.
|
|
|
When choosing an explosive route, go with the ______ one.
|
Safest
|
|
|
What is the purpose of placards?
|
To provide a general warning to all personnel and furnish specific guidance for fire fighting forces and other personnel responding to an emergency.
|
|
|
Which TO provides information for which placard to use?
|
11A-1-46
|
|
|
When should a placard not be used when transporting weapons?
|
When transporting nuclear weapons.
|
|
|
Where do you stop to remove or install placards on your vehicle?
|
At the entry control point of the weapons storage area.
|
|
|
What information does TO 11-1-38 provide?
|
It provides info on the correct positioning of munitions, provides tie-down procedures, and lists the accerssories you need for each trailer.
|
|
|
Where can you find information on submitting improvements on TO 11-1-38?
|
The introduction
|
|
|
If you make working copied of TO 11-1-38, what must they contain?
|
The title and A pages, sections I and II, and applicable -38/local positioning/tie-down procedures. Also must contain procedures for munitions assigned to unit.
|
|
|
If there is a conflict between the illustrations in TO 11-1-38 and the written directions, which take precedence?
|
Written procedures
|
|
|
Which direction must MK82 bombs face on a 141 trailer?
|
They may face either front or back
|
|
|
When loading or unloading GP bombs, when may you move one bomb over the other?
|
Never
|
|
|
What is the maximum number of GBU-24s you can load on a 141 trailer?
|
Two
|
|
|
Which direction does a GBU-15 face while loaded on a 141 trailer?
|
Forward
|
|
|
How many chock are required to load the maximum quantity of cluster bombs on a 141 trailer?
|
16 bomb chocks
|
|
|
Which direction are the lugs pointing on the SUU-25 dispenser when it's on a 141 trailer?
|
The lugs are up
|
|
|
What happens if you attempt to pick up a single CNU-300-series container with the forklift tines in the end slots?
|
Tipping or dropping occur. It's prohibited unless stability is maintained and the container is securely tied to forklift.
|
|
|
What is the maximum number of AIM-9L missiles you can load on a 141 trailer using M-10 adapter assemblies?
|
10
|
|
|
What is the maximum number of AIM-120 missiles you can load on a 141 trailer using M-10 adapter assemblies?
|
10
|
|
|
What must you install when using the M-10 adapters with 141 trailers?
|
Three horizontal stabilizer bars
|
|
|
Which directionshould MK82 bombsface when loaded on a 110 trailer using the chocks and trolleys?
|
Nose to Nose
|
|
|
How are bombs with BSU-50 fins positioned on 110 trailers?
|
Nose to tail
|
|
|
What is the maximum number of GBU-12s you can load on a 110 trailer?
|
Nine
|
|
|
Where are the wing and control containers positioned on the 110 trailer loaded with two GBU-15s?
|
2 wings and 4 ctrl surfaces on the rear between 2 munitions. Wings are upright with the angle face rear. Ctrl surfaces are between trailer rail assemblies and wings
|
|
|
What is the maximum number of SUU-25 dispensers you can load on the 110 trailer?
|
10
|
|
|
How do you route the tie-down straps when positioning an AGM-65 reloaded on an LAU-88?
|
Do not run tie-down straps over the missiles or LAU-88/A launcher as damage can occur. Route the fixed hook end of the strap around the 114/E tie-down bar nearest each strap and secure to appropriate tie-down rings.
|
|
|
Which type of trailers are most likely to be used for munitions delivered to bomber aircraft?
|
25-foot or 40-foot trailers.
|
|
|
What is the maximum number of M-117 bombs you can load on the 25-foot trailer.
|
15
|
|
|
What special equipment is required to load SUU-65 dispensers onto a 40-foot trailer?
|
6 load binders and 6 10,000 PSI chains.
|
|
|
What items are used to positively identify equipment as nuclear certified?
|
Either the nameplate, label, or historical documents for the item and verify the item is located in Master Nuclear Certification List.
|
|
|
Explain two ways to locate a piece of equipment in the Master Nuclear certification List
|
Use the NSN or the item nomenclature on the nameplate and use the MNCL to locate the trailer by NSN.
|
|
|
What test equipment requires nuclear certification?
|
Equipment used to test and verify the proper functioning of critical circuits, assemblies, and devices associated with nuclear bombs and warheads in all nuclear systems.
|
|
|
List two examples of common multipurpose test equipment that do not require certification.
|
AN/PSM-6 and AN/PSM-37
|
|
|
List some examples of general- or special-purpose hand tools that do not require certification.
|
Pliers, wrenches, vacuum cleaners, screwdrivers, magnifiers, pry bars, connector removal/pin-straightening tools, and manually operated hydraulic floor or pallet jacks.
|
|
|
Explain what damage to the MB-1 tie-down/chain assembly warrants replacing the assembly.
|
Replace the tie-down device if it has any cracks or bent/worn part. Replace the chain if you find any deformed, cracked, or damaged links.
|
|
|
What preparation is required for MB-1 tie-down device installation?
|
To prepare the tie-down device for installation, fully extend the hook and open the chain recess.
|
|
|
Why is it important to evenly tighten the chain assemblies around the container?
|
Don't tighten one chain to the extent that the tension is great enough to dislocate the container before the remaining assemblies are tightened.
|
|
|
If you can't remove the tension on the MB-1 chain assembly by using the locking lever, what should you do?
|
Wear a glove to protect your hand and manually restrain the chain as you activate the MB-1 quick-release lever.
|
|
|
When you are using a load binder with a chain, where is the excess chain located?
|
Between the load-binder hooks.
|
|
|
Why are you not allowed to use an extension (cheater) to close the load-binder handle?
|
Using an extension (cheater) bar can place too much pressure on the container and trailer tie-down points.
|
|
|
How do you measure a load binder with cable?
|
To measure the assembly's length, close the load binder and "run in" the turnbuckle to its shortest length. Make your measurement from the inside curves of the clevises.
|
|
|
What are the length tolerances for the cable-type load binders?
|
Between 85.75 inches minumum to 87.0 inches maximum.
|
|
|
What is the rated working load of the CGU-1/B strap?
|
5,000 pounds
|
|
|
Which TO authorizes you to use two CGU-1/B straps for one MB-1 tie-down assembly?
|
TO 11N-45-51C, transportation of Nuclear Weapons Materiel, Military criteria for Shipment.
|
|
|
What do all bolsters have in common?
|
All bolsters have slots, either built in or added, to accommodate foklift tines.
|
|
|
How are bolsters rated for maneuverability and roadability?
|
Limited maneuverability, maneuverable, limited roadability, and roadable.
|
|
|
What is the bare-hand test on bolsters?
|
Place your bare hand on the caster for a minu
|
|
|
How are double-stacked weapons moved?
|
By hand,forklift, or trailer.
|
|
|
What is an important thing to remember when using a forklift or sling to load weapons on trailers?
|
Not to exceed the weight limit of the lifting device.
|
|
|
How do you prevent damage to cables or trailer tie-down clasps when tightening them?
|
Make your final tension adjustments with the turnbuckle while the load binder is in the closed position. After the weapon is secure, tighten the wing nut securely against the turnbuckle.
|
|
|
How does the DOD ship weapons?
|
By truck or air
|
|
|
What types of aircraft are normally used for DOD shipments?
|
C-17 or C-130 aircraft.
|
|
|
What is the primarymethod for transporting nuclear weapons?
|
The Safe-Secure Trailer/Safeguards Transporter.
|
|
|
List four things to consider when planning a nuclear weapons movement.
|
Known and possible hazards; Intel estimates of threats associated with the route; The type of weapons and method of shipment; The availability of security forces and resources
|
|
|
Who is notified in the event of an accident or delay involving a shipment of nuclear weapons?
|
The shipping and receiving commanders
|
|
|
How often are couriers certified?
|
At least annually
|
|
|
Why would a DOE convoy seek sanctuary (Safe Haven) at a military base?
|
As a result of a hostile or emergency situation
|
|
|
What type of operational movement happens inside the WSA?
|
An intra-area movement
|
|
|
List two examples of outside WSA weapon movements
|
Hot cargo pad for a special-assignement airlift mission; Flight line for alert aircraft upload
|
|
|
What is a breakout of nuclear weapons?
|
The term breakout is used to describe the action of removing weapons from a structure.
|
|
|
What are the requirements for a vehicle operator in a convoy?
|
Vehicle operators must be fully qualified in the operation of the particular vehicle, have in their possession a valid operator's permit, and be certified to transport weapons.
|
|
|
What is the most difficult task for escort guards when driving in a convoy?
|
To keep other vehicles from entering the convoy
|
|
|
What isused in the event of duress during a convey?
|
A secure duress code word or signal
|
|
|
What is the preferred mode of the general transportation of explosives?
|
Cargo-type trucks and truck-tractor-drawn semitrailer
|
|
|
What placard should be used in a movement of 500 pounds of compressed gas and 1,000 pounds of flammable gas?
|
Dangerous
|
|
|
What is the lowest level in the chain of command that is authorized to interpret TO 11-1-38?
|
Munitions Flight Chief
|
|
|
Where in TO 11-1-38 do you find information on reproducing the TO to meet local needs?
|
The Introduction
|
|
|
Evne though TO 11-1-38 has its own safety section, with which direction must you still comply when transporting bombs to the flight line?
|
AFMAN 91-201
|
|
|
What is the maximum load capacity of GBU-12s on 141 trailers
|
4
|
|
|
What precaution must be taken when handling GBU-15(V)/Bs?
|
Ensure that the protective dome cover is in place
|
|
|
What is the approximate positioning of the first CNU-300-series container loaded on a 141 trailer?
|
18 inches from the front of the trailer with the projeciles facing the rear.
|
|
|
What is the maximum load capacity of AIM-7s using the M-10 adapter on a 141 trailer?
|
8
|
|
|
How are two GBU-15s positioned on a 110 trailer?
|
Nose to Tail
|
|
|
what is the lug position for cluster bombs on a 110 trailer?
|
All lugs pointed up
|
|
|
What must be done with the lids of the CNU-300-series containers that are no secured during transportation?
|
Route a tie-down strap over the tops of all containers and secure to tie-down rings?
|
|
|
What is the lug position for general-purpose bombs on a 40-foot trailer?
|
Either all lugs up or all lugs down.
|
|
|
Which of the following are constructed and attached to the bed of a 40-foot trailer to facilitate support of rounded munitions?
|
Wooden Rails
|
|
|
How are items identified as being nuclear certified?
|
Positive identification by a nameplate or label
|
|
|
When using MB-1 chain assemblies to tie down nuclear weapons, you are required to tighten the chain until you cannot deflect the chain more than how much of an inch with nominal hand pressure?
|
3/4 of an inch
|
|
|
How many CGU-1/B straps are you authorized to use for one MB-1 tie-down assembly?
|
Two
|
|
|
How do you extend the CGU-1/B strap
|
Release the adjusting mechanism; pull the strap
|
|
|
Many nuclear weapon bolsters are designed with an attachment point for a tow bar, but one exception is the
|
H1125
|
|
|
How many miles can a "maneuverable" bolster be towed over hard surfaces before a "bare hand" test of the casters is required?
|
Two miles
|
|
|
If a container is rated "roadable", you can tow it at speeds up to...
|
20 mph over primary roads
|
|
|
The key factors to consider during a nuclear weapons movement are...
|
safety and security
|
|
|
Which term describe the type of area used during a delay of an off-base shipment involving nuclear weapons?
|
National defense
|
|
|
What code word is used when a DOE convoy seeks sanctuary during an emergency?
|
Safe Haven
|
|
|
What IMT is used to transfer custody of misile warheads?
|
AF IMT 514
|
|
|
When are nuclear weapons moved by convoy?
|
All weapons movements are by convoy.
|
