Reading...
Play button
Play button
Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
95 Cards in this Set
- Front
- Back
|
The estimated percent of accidents caused by nature is
a. 2 b. 4 c. 6 d. 8 |
a. 2
|
|
|
The safety training phase described as an effective tool that creates a lasting impression for a new airman is
a. initial b. general c. supervisor's d. sustained job safety |
a. initial
|
|
|
The responsibility for initiating a lost tool report belongs to the
a. CTK support section b. expediter or production supervisor c. flight chief or flight commander d. person issued the tool |
d. person issued the tool
|
|
|
The lowest person authorized to clear a red X when a tool is lost CANNOT be located is the
a. maintenance supervisor b. wing commander c. aircraft engineer d. crew chief |
a. maintenance supervisor
|
|
|
The optimum temperature to cool sealants mixed in an automatic mixing machine is
a. 70 degrees F b. 75 degrees F c. 80 degrees F d, 85 degrees F |
a. 70 degrees F
|
|
|
Temporary storage of hazardous materials at a central accumulation point cannot exceed
a. 30 days b. 60 days c. 90 days d. 120 days |
c. 90 days
|
|
|
Hazardous Waste Managment System rules are published by
a. the US Air Force b. MAJCOM c. DOD d. the EPA |
d. the EPA
|
|
|
Radiation hazards are affected by
a. strength of emission, time of day and, input power b. strength of emission, time of exposure, and weather c. input power, weather, and number of personnel in the area d. time of exposure, amount of training, and number of operating units |
b. strength of emission, time of day and input power
|
|
|
Normally, the safe distance behind an operating jet engine exhaust is
a. 125 feet b. 150 feet c. 175 feet d, 200 feet |
d. 200 feet
|
|
|
The noise intensity of a jet engine is the greastest toward the rear at a
a. 15 degree angle at either side b. 45 degree angle at either side c. 65 degree angle at either side d. 95 degree angle at either side |
b. 45 degree angle at either side
|
|
|
The symptom that is NOT a sign of noise fatigue is
a. dizziness b. emotional irritability c. a feeling of emptiness d. impairment of mental concentration |
c. a feeling of emptiness
|
|
|
A fire extinguisher's pressure is within a safe operating range when the gauge needle is within the
a. red markings b. black markings c. green markings d. orange markings |
c. green markings
|
|
|
Aircraft oxygen servicing or draining is prohibited within how many feet of hangars or structures?
a. 25 b. 50 c. 75 d. 100 |
b. 50
|
|
|
Individuals NOT directly involved in nitrogen servicing should be outside a
a. 15-foot radius b. 20-foot radius c. 25-foot radius d. 50-foot radius |
b. 20 foot radius
|
|
|
Under IDEAL conditions, an aircraft is said to be operationally ready when
a. the aircraft forms are checked b. it is released by production scheduling c. all minor discrepancies are completely resolved d. the required inspection and servicing are complete |
d. the required inspection and servicing are complete
|
|
|
As fireguard, position yourself even with the
a. tail of the aircraft and at a 30 degree angle inboard of the engine being started b. tail of the aircraft and at a 30 degree angle outboard of the engine being started c. nose of the aircraft and at a 45 degree angle inboard of the engine being started d. nose of the aircraft and at a 45 degree angle outboard of the engine being started |
d. nose of the aircraft and at a 45 degree angle outboard of the engine being started
|
|
|
The condition MOST LIKELY to cause aircraft damage is
a. tornadoes b. hurricanes c. sudden local storms d. predicted heavy storms |
c. sudden local storms
|
|
|
If no maximum wind velocity is specified in the aircraft technical order the maximum wind velocity, as prescribed by Air Force Occupational Safety and Health Standard 91-100, Aircraft Flight Line-Ground Operations and Activities, allowed during aircraft jacking is
a. 15 mph b. 25 mph c. 35 mph d. 45 mph |
a. 15 mph
|
|
|
During desert operations, lubrication should be done
a. after every aircraft recovery or prior to every flight b. as often as possible and as abundantly as possible c. at least weekly and as liberally as possible d. only when necessary, and then sparingly |
d. only when necessary, and then sparingly
|
|
|
The F-2 lifting bag is designed to lift
a. 22,000 pounds to a maximum of 6 feet b. 22,000 pounds to a maximum of 8 feet c. 24,000 pounds to a maximum of 6 feet d. 24,000 pounds to a maximum of 8 feet |
c. 24,000 pounds to a maximum of 6 feet
|
|
|
A MAJOR drawback of using pneumatic lifting bags is
a. instability b. time consumption c. training requirements d. manning requirements |
a. instability
|
|
|
The method of aircraft hoisting confined to emergencies when no other method is available is
a. cribbing b. lifting bags c. crane hoisting d., aircraft jacking |
c. crane hoisting
|
|
|
The type of technical order library that does not need to maintain its currency is
a. training b. aircraft c. reference d. operational |
c. reference
|
|
|
In the second grouping of a TO number, the alpha character in parentheses means the
a. basic aircraft mission b. modified aircraft mission c. aircraft production series d. type of TO, instruction, or procedure |
b. modified aircraft mission
|
|
|
The TOTAL number of Air Force TO catalogs is
a. one b. two c. three d. four |
a. one
|
|
|
The directional flow of the schematics in the troubleshooting manual is from the
a. top of the diagram to the bottom of the diagram b. resulting action to the system initiating the action c. left side of the diagram to the right side of the diagram d. right side of the diagram to the left side of the diagram |
c. left side of the diagram to the right side of the diagram
|
|
|
Inspection work cards are known as
a. scheduled inspection and maintenance requirements manuals b. methods and procedure technical orders c. technical manuals d. abbreviated TO |
a. scheduled inspection and maintenance requirements manuals
|
|
|
Due to their potential for harm, commanders are required to ensure immediate action TCTO are distributed to all affected personnel within
a. 2 hours after receipt b. 4 hours after receipt c. 24 hours after receipt d. 72 hours after receipt |
b. 4 hours after receipt
|
|
|
The type of TO improvement issued for all TCTO deficiencies is
a. record b. urgent c. routine d. emergency |
b. urgent
|
|
|
The nondirective publication that may cite forms and provide guidance on completing them, but can't enforce whats on the form is
a. directory b. pamphlet c. instruction d. supplement |
b. pamphlet
|
|
|
In order of increasing capability, the Air Force's varying degrees of maintenance capabilities are
a. department, intermediate or field b. organizational, field, or intermediate c. organizational, intermediate, or depot d. departmental, organizational, or depot |
c. organizational, intermediate, or depot
|
|
|
The type of maintenance that ensures equipment is ready and available at the time of need is
a. unscheduled b. preventative c. corrective d. protective |
b. preventative
|
|
|
The most common excuse for taking short cuts is
a. time restraints b. people shortage c. money shortage d. parts availability |
a. time restraints
|
|
|
The prime contributions to dropped objects are
a. chaff/flare discharges b. latches and fasteners c. jettisoned fuel tanks d. hung weapons |
b. latches and fasteners
|
|
|
In most units, the responsibility for investigating dropped objects rests with
a. the FOD prevention office b. the operations commander c. the flight safety officer d. quality assurance |
d. quality assurance
|
|
|
The responsibility for FOD prevention belongs to
a. the logistics and operations group commanders b. the immediate supervisor c. the wing commander d. everyone |
d. everyone
|
|
|
The method that cannot be used to search for the lost tools is
a. X-ray b. depaneling c. visual search d. magnetic particle |
d. magnetic particle
|
|
|
The information that the configuration management subsystem ensures is loaded properly into the maintenance information system database is
a. damaged and spare items b. expired and outdated items c. recurring and repeat replacement items d. select serially controlled and time change items |
d. select serially controlled and time change items
|
|
|
The IMDS is the production-oriented, automated maintenance management system at the
a. MAJCOM level b. wing level c. base level d. unit level |
c. base level
|
|
|
The IMDS subsystem that provides information about jobs performed by maintenance activities is the
a. Job Data Documentation b., maintenance data collection c. Maintenance Information System d. reliability and maintainability system |
a. Job Data Documentation
|
|
|
The GAS is normally sent out
a, 90 days after graduation b. six months after graduation c. within 10 work days after graduation d. within 10 calender days after graduation |
a, 90 days after graduation
|
|
|
The method that cannot be used to search for the lost tools is
a. X-ray b. depaneling c. visual search d. magnetic particle |
d. magnetic particle
|
|
|
A list of training courses available for an AFSC can be found in the
a. CFETP, Part 1 b. AFJQS c. Command JQS d. CFETP, Part II |
d. CFETP, Part II
|
|
|
Tasks that a person is expected to perform in a duty position or WC but are not included in the CFETP, Part II, or AFJQS are listed
a. on an AF Form 797, Job Qualification Standard Continuation/Command JQS b. in the AF IMT 623A, On-the-Job Training Record Continuation Sheet c, in the CFETP, Part 1 d. in the AFJQS |
a. on an AF Form 797, Job Qualification Standard Continuation/Command JQS
|
|
|
The first step taken when reviewing an Air Force Technical Order (AFTO) 244 is to
a. match the ID number on the form with the ID number on the unit b. ensure all TCTOs have been done c. check the operational status of the unit d. check the inspection status of the unit |
a. match the ID number on the form with the ID number on the unit
|
|
|
The two maintenance stands on which C-1 maintenance stand can be installed as an extension are the
a. B-1 and B-2 b. B-1 and B-4 c. B-2 and B-4 d. B-4 and B-5 |
a. B-1 and B-2
|
|
|
The maintenance stand that has an adjustable height of 13'-20' is the
a. B-1 b. B-2 c. B-4 d. B-5 |
b. B-2
|
|
|
The maintenance stand that is a scissor type is the
a. B-1 b. B-2 c. B-4 d. C-1 |
c. B-4
|
|
|
The lifting of an aircraft jack is called a
a. ram b. plunger c. hand pump d. release valve |
a. ram
|
|
|
The low- and high-pressure capabilities, in psig, of the NSU-L75 nitrogen servicing init are
a. 0-300; 300-3,500 b. 0-300; 300-3,600 c. 05-350; 350-3,500 d. 05-350; 350-3,600 |
d. 05-350; 350-3,600
|
|
|
The usable pressure range, measured in the psi, of the MC-1A air compressor is
a. 0-200 psi b. 0-350 psi c. 0-3,200 psi d. 05-3,500 psi |
c. 0-3,200 psi
|
|
|
The MC-2A air compressor is capable of delivering air at a maximum pressure, measured in psi of
a. 200 b. 300 c. 3,500 d. 3,600 |
a. 200
|
|
|
The maximum BTUs per hour output of the H-1 heater is
a.160,000 b. 350,000 c. 400,000 d. 650,000 |
c. 400,000
|
|
|
The new generation heater oil burner and combustion blower are powered by
a. 12-volt battery b, a diesel engine c. 60- Hz alternator d. 60-volt generator |
b, a diesel engine
|
|
|
The temperature range the C-10 air conditioner is capable of delivering conditioned air at is
a. 47 degrees F- 150 degree F b. 47 degrees F- 200 degree F c. 57 degrees F-150 degree F d. 57 degrees F- 200 degree F |
b. 47 degrees F- 200 degree F
|
|
|
The FL-ID floodlight consists of two
a. 100 watt lamp fixtures b. 1,000 watt lamp fixtures c. 10,000 watt lamp fixtures d. 110,000 watt lamp fixtures |
b. 1,000 watt lamp fixtures
|
|
|
The unit capable of providing AC and DC electrical power, in addition to pneumatic power, for ground maintenance is the
a. A/M32A-95 b. A/M32A-86 c. A/M32A-60 d. AF/M-32-3 |
c. A/M32A-60
|
|
|
The MK-3A-1 is driven by a
a. diesel engine b. electric motor c. gasoline engine d. hydraulic motor |
b. electric motor
|
|
|
The MB-4 tractor incorporates
a. two-wheel steering, two wheel drive b. two-wheel steering, four wheel drive c. four-wheel steering, two wheel drive d. four-wheel steering, four wheel drive |
d. four-wheel steering, four wheel drive
|
|
|
Aluminum alloy washers are used with steel bolts on aluminum alloy parts in low-torque applications to
a. reduce shearing b. prevent vibration c. prevent corrosion d. reduce shimming |
c. prevent corrosion
|
|
|
Special bolts are identified by
a. a zinc-plated nickel steel covering b. a galvanized-plated steel covering c. the bolt head marked with a triangle d. the bolt head marked with the letter S |
d. the bolt head marked with the letter S
|
|
|
The bolt used where heavy tension of lengthwise stress must be sustained is a
a. stud b. clevis c. eyebolt d. hexhead |
d. hexhead
|
|
|
The number of threads that must be showing through a self-locking nut for maximum locking effect is at least
a. one b. two c three d. four |
b. two
|
|
|
Aircraft cable size is determined by its
a. length b. radius c. diameter d. circumference |
c. diameter
|
|
|
A 7 x 19 cable has
a. 7 strands with 19 wires per strand b. 7 wires with 19 strands per wire c. 133 wires per strand d. 133 strands per wire |
a. 7 strands with 19 wires per strand
|
|
|
The correct way to detect broken wires on a cable is to
a, pass a cloth along the length of the cable b. use a strong light along the length of the cable c. carefully run your hand along the length of the cable d. pass a thin piece of paper along the length of the cable |
a, pass a cloth along the length of the cable
|
|
|
A push-pull rod end engagement is checked
a. using a depth gauge to check end play b. by ensuring no lateral movement exists c. using inside caliper to check the rod end bearing d. by inserting safety wire in the hole in the end of the terminal |
d. by inserting safety wire in the hole in the end of the terminal
|
|
|
A hose may bear a colored indicator stripe to show
a. the contents of fluid passing through the hose b. the type of material the hose is made of c. its direction of natural lay d. the direction of fluid flow |
c. its direction of natural lay
|
|
|
When using 0.032-gage safety wire, there should be how many turns per inch?
a. 7-12 b. 8-10 c. 8-12 d. 10-13 |
a. 7-12
|
|
|
When securing widely spaced bolts by the double-twist safetying method, the maximum number of bolts that may be wired in a series is
a. three b. four c. five d. six |
a. three
|
|
|
When is it permissible to reuse cotter pins?
a. Never b. In emergencies c. When the mission dictates it d. when they are constucted of pliable material |
a. Never
|
|
|
On a standard electrical connector, the key and keyway are located
a. adjacent to the A or 1 pin b. adjacent to the B or 2 pin c. at the 6 oclock position on cannon plug halves d. at a 12 oclock position on the cannon plug halves |
a. adjacent to the A or 1 pin
|
|
|
To tighten cannon plugs do NOT use
a. fingers b. strap wrench c. channel lock pliers d. padded conduit pliers |
c. channel lock pliers
|
|
|
The number of positions on the function switch of the AN/PSM-37 multimeter is
a. two b. three c. five d. seven |
d. seven
|
|
|
To measure current flow, you connect an AN/PSM-37 multimeter in
a. series in the circuit b. parallel in the circuit c. series with the component d. parallel with the component |
a. series in the circuit
|
|
|
When the H symbol is shown on the Fluke multimeter display, the
a. manual range mode is indicated b. touch-hold mode is in use c. ohms function is selected d. meter is zeroing itself |
b. touch-hold mode is in use
|
|
|
When measuring restistance on a Fluke multimeter, the letter OL indicate
a. error b. infinity c. overload d. ohms low |
c. overload
|
|
|
Prior to using a torque wrench, cycle the torque wrench through the breakaway torque at the
a. maximum setting at least four times b. maximum setting at least six times c. lowest setting at least four times d. lowest setting at least six times |
b. maximum setting at least six times
|
|
|
The responsibility for ensuring good supply discipline is practiced resides with
a. base commanders b. squadron commanders c. supervisors at all levels d. squadron quality assurance (QA) section |
c. supervisors at all levels
|
|
|
Shop stock should not normally exceed
a. 30-days usage or the U/I or unit pack, whichever is greater b. 60-days usage or the U/I or unit pack, whichever is greater c. 90-days usage or the U/I or unit pack, whichever is greater d. 120-days usage or the U/I or unit pack, whichever is greater |
c. 90-days usage or the U/I or unit pack, whichever is greater
|
|
|
The expandability, recoverability, reparability code that designates a repair cycle asset is
a. XB b. XF c. ND d. DX |
b. XF
|
|
|
The DD Forms easily identified by their green margins and letters are the
a. 1577-2, Unserviceable (Reparable) Tag- Material, and 1577-3, Unserviceable (Reparable) Label-Material b. 1576, Test Modification Tag- Material, and 1576-1, Test Modification Label-Material c. 1575, Suspended Tag- Material, and 1575-1,Suspended Label -Material d.1574, Serviceable Tag- Material, and 1574-1,Serviceable Label -Material |
a. 1577-2, Unserviceable (Reparable) Tag- Material, and 1577-3, Unserviceable (Reparable) Label-Material
|
|
|
The deficiency report (DR) category that results in a work line stoppage is
a. I b. II c. III d. IV |
a. I
|
|
|
Engines overhauled by depot are covered against defects in workmanship for
a. 200 hours of operation or one year from the date of receipt b. 100 hours of operation or one year from the date of receipt c. 200 hours of operation or six months from the date of receipt d. 100 hours of operation or six months from the date of receipt |
b. 100 hours of operation or one year from the date of receipt
|
|
|
The Air Force Technical Order Form 781 must be removed from the forms binder
a. before the first day of flight b. before each thruflight inspection c. after the event number is entered at the maintenance debriefing d. after each maintenance action with an assigned job control number |
c. after the event number is entered at the maintenance debriefing
|
|
|
The Air Force Technical Order Form 781K is used to document
a. support general work b. replacement items c. daily flying time d. engine data |
d. engine data
|
|
|
Responsibility for maintaining the Air Force Technical Order 781-series forms binder rests with the
a. crew chief b. flight chief c. branch chief d, section chief |
a. crew chief
|
|
|
The action necessary to clear an erroneous red X symbol is
a. an authorized individual signs the INSPECTED BY block and initials over the symbol b. an authorized individual signs the CORRECTED BY block and initials over the symbol c. place the statement "Symbol entered in error" in the DISCREPANCY block and sign the INSPECTED BY block d. place this statement "Symbol entered in error" in the DISCREPANCY block and sign the CORRECTED BY block |
a. an authorized individual signs the INSPECTED BY block and initials over the symbol
|
|
|
The symbol entered on the forms if an aircraft exceeds the PDM cycle by 90 days and an extension is not granted is a
a. red X b. red dash c. red diagonal d. black signature |
a. red X
|
|
|
The inspection usually performed just prior to takeoff and that may include operational checks of some systems is the
a. preflight b. thruflight c. in progress d. end-of-runway |
d. end-of-runway
|
|
|
The BPO is performed to
a. prepare the aircraft for another flight b. determine the flight status of the aircraft c. prepare the aircraft for the first flight of the day d. determine if the aircraft is suitable for another flight |
d. determine if the aircraft is suitable for another flight
|
|
|
If an aircraft is idle for more than 30 or 90 days, the inspection required is
a. phase b. special c. calendar d. acceptance |
c. calendar
|
|
|
The type of inspection that ensures the completeness of historical documents is
a. phase b. special c. calendar d. acceptance |
d. acceptance
|
|
|
The AF IMT 2691 is used to
a. serve as a receipt document b. serve as a shipping document c. transfer aircraft -21 TO equipment d. account for aircraft -21 TO equipment |
d. account for aircraft -21 TO equipment
|
|
|
Corrosion or deterioration of a metal part continues until the part is
a. painted b. heat treated c. chemically treated d. exhausted or salvaged |
d. exhausted or salvaged
|
