Relative density

Introduction and Theory: The lab conducted was to investigate the density of not only copper but also diet and non-diet soda. Techniques used in the experiment included water-displacement, measuring copper’s dimensions, and using volumetric pipettes to measure out specific soda volumes. Beginning Question(s): How does the use of two experimental methods, improve the chances of calculating the density of copper? How does the density of non-diet soda compare to that of diet soda measured at…

Introduction: Water quality is the scientific measurement describing the cleanliness of water and/or the condition of the water being studied. Factors that used to describe water quality are pH, Dissolved Oxygen, Temperature, Turbidity, Nitrogen, Biological Oxygen Demand (BOD), Fecal Coliform, Phosphate, and Total Solids. Water quality is important to know because water is a necessary part of life, and people need to know how clean the water they’re using is. Water quality is important for…

water into the beaker, and then reweighing the beaker. Next, the weight of water was calculated by subtracting the weight of the empty beaker from the weight of the beaker containing water. These values were then converted to water volume using the density of water at a temperature of 19.5 °C; 0.998 g/ml. The weight of water measurements, 9.82 g, 9.90 g, and 9.94 g, were converted to water volume by dividing by 0.998 g/ml as shown below. Volume = (9.82 g) / (0.998 g/mL) = 9.84 mL Volume =…

current velocities with the following equation where statistical data is not available. V_(C_Wind )=0.015∙U_(1 hour,10 m) Equation 3.1 Directions The non-collinear environment as specified in DNV-OS-E301 is used in the analysis. The wind is at 30° relative to the waves while the current is applied at 45°. The Pierson – Moskowitz spectrum is used for the random waves. For wind, the ISO spectrum is used. The current profile is assumed constant with time. The magnitude and the directions of the…

Injection Machine 4.6.1 Calculation of the Injection Volume Figure 4-8 shows the volume of plastic parts by Solidworks modeling. Figure 4-8 Volume of the Stress Cone Plastic parts volume: Vplastic = 4.198 × 10-5 m3 = 41.98 cm3 Plastic parts density: ρ = 1.2 g/cm3 Plastic parts quality: mplastic = ρVplastic = 1.2 × 41.98 = 50.376 g 4.6.2 Preliminary Estimation of the Gating System Although the gating system of condensate cannot determine the exact value prior to design, it can be…

Our experiment was centered on taking four testing groups and setting a baseline level of dehydration across all four groups. From there each group would be assigned water, coke, Gatorade or remain dehydrated. The test subjects would then consume their assigned drinks based on their body weight. Urine would then be collected at thirty-minute time intervals to measure urine changes. The goal of our experiment was to determine the influence of fluids being introduced into the body of various…

Aim The aim of this practical is to measure the effect of volume, density and temperature. It is also help to be familiar with variety of common laboratory technique. Materials Weighting scale Container with lids 20 and 10 ml Volumetric pipette Beaker Thermometer Test Tubes Volumetric flask Natural Rubber Pipette Filler Micropipette tips Tips boxes Method There are two pipette, choose one which you using in whole practical. Label and weight accurately, to 4 decimal places. Collect…

By examining Figure 4, we can see the relationship between density and molar mass to be a proportional relationship. The positive slope of the scatter plot confirms this relationship. This means that as molar mass of is greater, the density of the gas will also be greater, and if the molar mass of a gas is smaller, the density of the gas will be smaller. For example, hydrogen gas will have a lower density than nitrogen gas because hydrogen has a smaller molar mass than nitrogen.…

The Relationship between Mineral Type and Density (g/ml) Purpose/Introduction: The purpose of this lab was to understand the relationship between minerals and density, the ratio of mass to volume, particularly, how density can be used to identify mineral type. In the lab, two samples of the mineral, feldspar, were measured for mass and volume in order to calculate their density. Many of the mineral tests yielded qualitative data, such as color, streak, luster, and crystal shape, which can be…

Experiment 2: Aim: In this experiment you will determine the mass of a single drop of water by a graphical method. You will evaluate its uncertainty. Data: Table 1: Number of Drops: Mass of Beaker + drops/g (0.01g) 1 2.36 g 2 2.38 g 3 2.40 g 4 2.44 g 5 2.46 g 6 2.48 g 7 2.50 g Chart 1: Analysis: The mass of 1 drop of water is 0.4g. By taking the total mass and dividing it by the number of drops we can figure out the average mass of a drop of water. However the number of drops should…