Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
62 Cards in this Set
- Front
- Back
What structural areas ared designed to allow maniteance personal to inspect or service aircraft components?
|
doors
|
|
What is provided on some large doors to provide access for inspections?
|
small hinged doors
|
|
What components are used to guard against accidental firing of ejection seats?
|
Safety pins
|
|
How do independent positioning determning subsystems function?
|
Independent of ground equipment
|
|
Which is not part of an engine indicating system?
|
water temperature
|
|
Ejection seats in a millitary aircraft are particulary dangerous beacause?
|
the system contains an explosive charge
|
|
What is normally considered a minimun safe distance from the intake of an operating jet engine?
|
25 feet to the front and sides of the engine intake
|
|
When approaching overheated aircraft wheels always approach the wheel from?
|
the front of behinde the wheel
|
|
What happens when radio-frequency energy is absorbed in the tissue of your body?
|
heat is produced
|
|
What is the minimum safe distance from an ultra-high frequency antenna when the assoicated transmitter is radiating power?
|
1 foot
|
|
The miniumumsafe distance from a high -frequency antenna when the associated transmitter is radiating power is?
|
5 feet
|
|
The variables upon which radiation hazards depend do not include the?
|
exerience of the operator
|
|
The maximum nosie level that is considered to be relatively safe is?
|
84 dBa
|
|
What is not a required action when working around moving machinery?
|
Wearing loose, comfortable clothing
|
|
Which is not an Airforce inspection concept?
|
Preflight
|
|
what type of inspection is a flight preparedness check?
|
Prefight
|
|
Which statement does not describe the programmed depot maintenance inspection concept?
|
applies to only units under the periodic inspection concept
|
|
When is the thruflight inspection performed?
|
Prior to takeoffs at intermediate stops
|
|
Which inspection is more extensive than the hourly postflight or basic postflight inspections and covers certain parts, areas, and systems of the aircraft that require less frequent inspection?
|
Periodic
|
|
Which inspection is designed to reduce the time an aircraft is out of commission for any given inspection?
|
Phase
|
|
When the home station check inspection becomes due during a mission, it is completed at the base?
|
to which the aircraft belongs
|
|
Which inspection includes a review of the forms for current status,a visual inspection of equipment for defects, and adequate servicing?
|
Operator
|
|
Acceptance inspections are performed when?
|
newly assigned support equipment arrives
|
|
Malfunctions documented on an AFTO Form 244, Industrial/Support Equipment Record, are the responsibility of.
|
arerospace ground equipment mechanics
|
|
The AFTO form 245 is used?
|
as a continuation sheet for part V of the AFTO form 244.
|
|
The AFTO form 781-series are not used to document aircraft?
|
componet repair
|
|
Except for battle damage,each discrepancy is documented on an AFTO Form?
|
781A
|
|
If you find a malfunction during an operational check, how do you document the malfunction on the AFTO Form 781A?
|
Sign off as OPS CK BAD and enter new malfunction.
|
|
Which AFTO Form is used to document maintenance status and servicing information?
|
781H
|
|
Who is responsiable for documenting engine cycles on an AFTO Form 781H?
|
crew cheif
|
|
Which AFTO Form is used to document aerospace vehical time and engine data, including operating time?
|
781J
|
|
Who is responsiable for making entries on the Aerospace Vehical-Engine Flight form?
|
Maintenance technician
|
|
Which AFTO Form allows you to record essential inspection and delayed maintenance data?
|
781K
|
|
Block C on the AFTO Form 781K is used to document?
|
inspection iteams that require inspection or testing at a specified hourly or calendar period
|
|
AFTO Form 78L is used to?
|
record the removal and installation of controlled cryptographic items
|
|
What helps to dissipate and lessen the effects of electrostatic discharges?
|
Humid air
|
|
Which is not a flight line preacaution used to protect electrostatic discharge sensitive components?
|
Using protective tote boxes
|
|
When working on electrostatic discharge sensitive devices in the shop area, you must use?
|
a grounding workbench
|
|
Which action action could pose a safety hazard to personnel in an electrostatic discharge protected area?
|
Use of certain ionizers
|
|
Shielded cable consists of?
|
a metallic braid over the insulation.
|
|
Which type of cable is used to carry radio-frequency power from one point to another?
|
Coaxial
|
|
Which is not a type of connector coupling?
|
Insertion
|
|
What is not a radio-frequency connector precaution?
|
Ensure a good grip when using pliers
|
|
The serial transmission bit rate for the Military Standard 1553B data bus is?
|
1 megabits per second (Mbps)
|
|
What is the structure of a Military Satandard 1553B data word?
|
20 bits long consisting of 3 sync, 16 data/command/status, and 1 parity bit
|
|
A millitary Standard 1553B data bus message must contain at least one command word with a maximum of?
|
32 data words
|
|
What is not a function of the Military Standard 1553B data bus mode codes?
|
Executing a bus controller broadcast command
|
|
Twisting an optic fiber during installation or maintenance results in?
|
reduced optical power transmission
|
|
What is used to convert fiber optic light transmissions to electrical signals?
|
photo diode
|
|
Optoelectronic transducers perform what function in a fiber optic transmission?
|
Convert optical engery to electrical energy
|
|
Utilizing exact dimensions for stripping wires ensures?
|
proper connection
|
|
Flux is designed to?
|
prevent oxygen from combining with the metal
|
|
Proper care of an electric soldering iron involves?
|
keeping the iron in a proper holder when you are not using it
|
|
What is of the utmost importance in the soldering process?
|
cleanliness
|
|
Which is not a type of solderless connector?
|
Connector splice
|
|
One purpose of crimper positioners is to?
|
put the pin contacts in the proper position.
|
|
The colored end of an insertion and extraction tool is used for contact?
|
insertion into a rear-release connector plug
|
|
One way of pressre and moisture sealing the back of a connector is to use?
|
silicone tape
|
|
The heat and air pressure required for proper installation of heat-shrink products is controlled by the?
|
tool operator
|
|
Electromagenetic pulse hardened cable is considered noreparable by local personnel if it has damage to the?
|
broken internal wires
|
|
To what precaution must you adhere prior to performing a wire repair job?
|
read all procedures in TO 1-1A-14
|
|
What is not considered to be a general precaution when lacing or tying wire groups or bundles?
|
tie all wire groups or bundles twelve inches or less apart
|