Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
59 Cards in this Set
- Front
- Back
What is the short side of a framing square called? |
tongue |
|
Which layout tool may be adjusted to serve as a marking gauge? |
combination square |
|
When a high-speed twist bit is used in metal, how is it kept cool? |
cutting oil on the bit keeps the bit cool |
|
What is a nail claw commonly called? |
cat’s paw |
|
Which tool is used to make small curved cuts in mouldings? |
coping saw |
|
What is the reason for staggering the nails when you drive nails along the length of a piece of wood? |
it prevents the wood from splitting |
|
Which tool is used to draw large circles? |
trammel points |
|
When drilling with a twist bit, what general rule should be followed? |
drill wood with high speed and steel with low speed |
|
The most often used table on the framing square is the _____________. |
rafter table |
|
Which tool should be used to mark a long, straight line? |
chalk line |
|
Which of the following describes the two types of heads on framing hammers? |
. smooth and serrated |
|
In construction, what does the term “plumb” mean? |
vertical |
|
What is the term for the saw cut through which the saw blade passes? |
kerf |
|
What are yellow-handled aviation snips used for? |
straight cuts |
|
The end vial of a carpenters level is used for levelling; checking level. |
False |
|
What is the name of the large, L-shaped squaring tool that has tables stamped on it? |
framing square |
|
What is the correct order for drilling in order to set the head of the screw below the surface? |
counterbore, pilot, and shank hole |
|
What is laying out stock to fit against an irregular surface called? |
scribing |
|
Which type of square allows the blade to turn to any angle? |
sliding T-bevel |
|
What is the name of the one-handed plane with a low blade angle? |
block plane |
|
What is the part of an auger bit that scores the outer circle of the hole called? |
spur |
|
What does the colour of the handles on aviation snips indicate? |
the direction in which curves may easily be cut |
|
In hot weather, what happens to the bubble in a level? |
it becomes smaller |
|
What should be raised to adjust a carpenter’s level into a level position when the bubble is found to be touching the right? |
The left side should be raised. |
|
What is the name of the triangular-shaped tool used to lay out 90- and 45-degree angles? |
Speed Square® |
|
What is most jobsite measuring done with? |
a pocket tape |
|
What are pliers designed for general use called? |
combination pliers |
|
When snapping a long chalk line, what should you make sure to do? |
keep the string from sagging |
|
Which tool is most commonly used for cutting gypsum board? |
utility knife |
|
In construction, what does the term “level” mean? |
horizontal |
|
In what classification of tools are hammers, bars, and pullers? |
dismantling tools |
|
What is a short, thin blade chisel that is preferred for finish work called? |
butt chisel |
|
What is necessary to allow the installation of plugs in screw holes? |
plugged pilot hole |
|
As a general rule, use nails that are _______________ longer than the thickness of the material being fastened. |
3 times |
|
What is the smallest imperial increment typically used by a carpenter? |
1/16" |
|
The set of saw teeth helps to prevent binding of the saw blade. |
True |
|
Which handsaw is used to make small diameter cuts? |
compass saw |
|
What is the technique of driving nails at an angle to fasten the end of one piece to another called? |
toe nailing |
|
Which tool is also known as a scriber? |
wing dividers |
|
Which plane is considered to be the best for all-around work? |
jack plane |
|
When you use a push-style handsaw, where should the face side of the stock be? |
up |
|
What is the metric equivalent of a 2" ´ 4"? |
38 ´ 89 mm |
|
The higher the number of the point size on a Phillips screwdriver, the ________________. |
larger the diameter of the point |
|
The concave surface on the bevel of a chisel is called a _________ |
hollow grind |
|
The size of a hammer is determined by the length of its handle. |
False |
|
When stretching a steel tape to lay out a measurement, how should you place the ring? |
so that the outside of the ring is on the starting line |
|
What size hole will a #10 auger bit bore? |
5/8 inch diameter hole |
|
When trimming the end of a board, which saw will result in the cleanest cut? |
crosscut saws |
|
Nails have more holding power when driven across the grain. |
True |
|
What is the second step in sharpening a badly dulled chisel? |
whetting |
|
What type of tools are named Spring-, C-, and Quick- ? |
clamps |
|
Which saw is used to cut metal? |
hacksaw |
|
When you use a handsaw, the face side of the stock should be______. |
up |
|
Which tool is used to control saw-cut angles of various degrees on finish lumber? |
mitre box |
|
Which of the following is a trick to keep the nail from splitting the wood? |
blunt the end of the nail before driving it into the wood |
|
When performing heavy framing a ______________- chisel is usually used, whereas a ____________- chisel is used more often for finish work. |
Firmer, Butt |
|
What is drawing lines parallel to the edge of a board called? |
gauging |
|
What diameter hole does a lock set usually require? |
2-1/8 inch (54 mm) |
|
What is the tool that hangs on a string to show absolute vertical called? |
plumb bob |