Reading...
Play button
Play button
Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
19 Cards in this Set
- Front
- Back
|
POWER SPREADER BACHO HS15-120
|
DESIGNED TO ROTATE 360 DEG UNDER PRESSURE. IT DEVELOPS 2000LB AT THE TIP AND 8000LB TOWARD THE BACK OF THE CHUCK
|
|
|
BACHO MAINTENANCE
|
-KEEP TEETH ON THE SPREADERS CLEAN, CLEAR OF DIRT AND GRIT AND FREE FROM BURRS
-IF A LEAK DEVELOPS IN THE UNIT TAK IT OUT OF SERVICE. IF YOU ARE LOOSING FLUID THEN YOU ARE LOOSING PRESSURE AND FORCE |
|
|
COME-A-LONG RIGID MODEL 584
|
THE COME-A-LONG WEIGHS 16LB AND CAN BE USED FOR LIFTING,PULLING AND LOWERING. IT IS DESIGNED TO WORK ON EITHER SINGLE OR DOUBLE CABLE.IT HAS A PULLING CAPACITY OF 2000LB ON A SINGLE CABLE AND A TRAVEL OF 18FT. ON A DOUBLE CABLE IT CAN PULL 4000LB AND TRAVEL 8 1/2 FT
|
|
|
MAINTENANCE OF THE COME-A-LONG
|
-ENSURE ALL GEARS ENGAGE ALL GEARS AND DISENGAGE EASILY
-USE SILICONE SPRAY -CHECK HANDLE FOR BENDING -CHECK THE UNIT HOOKS AND SAFETY LATCHES -CHECK THE FULL LENGTH OF THE CABLE FOR FRAYS OR FLATTENING. -THE CABLE SHOULD BE CLEANED AFTER EVERY USE -ALWAYS WORK WITH HOOKS IN THE UP POSITION. |
|
|
HACKSAW
|
CAN BE USED ANYWHERE METAL HAS TO BE CUT-ROOF POSTS
|
|
|
KEY HOLE SAW
|
CAN BE USED FOR CUTTING AROUND DOOR LOCKS, WHICH WILL ENABLE ACESS TO THE DOOR LATCH
|
|
|
CHANNEL LOCK PLIERS
|
CAN BE USED FOR BREAKING AWAY STEERING WHEEL COVERING,AND REMOVING LARGE BOLTS OR NUTS
|
|
|
SIDE CUTTERS
|
CAN BE USED ON LIGHT METAL SUCH AS SHEET METAL AND CAN ALSO BE USED TO CUT SHOULDER HARNESSING
|
|
|
SCREWDRIVER
|
MAY BE USED TO BREAK WINDOWS AND ASSIST WITH WINSHEILD REMOVAL
|
|
|
WIPER BLADE
|
IS AN EXCELLENT TOOL FOR BREAKING WINDOWS
|
|
|
BOLT CUTTERS
|
36 INCH CAN BE USED FOR CUTTING LOCKS,CHAIN OR STEERING WHEELS
|
|
|
UTILITY KNIFE
|
IS EXCELLENT FOR SEAT BELTS, REMOVING RUBBER SET WINDSHEILDS
|
|
|
FORCE RESCUE TOOL
|
THIS PIECE OF RESCUE EQUIPMENT IS 90% IMAGINATION TOOL.
|
|
|
HURST 32B SPREADERS
|
-EASILY RECOGNIZED BY THE SHORT WIDE ARMS
-WEIGHS 71 1/2 LBS OPENS TO 32 IN -HAS AN OPENING FORCE OF 18,500LBS AND A CLOSING FORCE OF 18800PSI -THIS UNIT HAS 2- 12FT CHAINS WITH HOOKS ON BOTH ENDS AND CHAIN SHORTENERS THEIR TENSILE STENGTH IS BETWEEN 60-70000 PSI |
|
|
MAINTENANCE OF SPREADERS
|
-UNIT SHOULD OPEN AND CLOSE SMOOTHLY
-THE THUMB CONTROL SHOULD OPERATE SMOOTHLY -THE UNIT SHOULD BE OPENED THE FULL 32" AND HELD UNDER LOAD FOR APPROX 5 SEC, THEN CLOSED AND HELD FOR 5 SEC WHILE CHECKING FOR LEAKS -KEEP THE HOSE COUPLING FREE FROM DIRT AND GRIME -PERIODICALLY LUBRICATE WITH SILICONE SPRAY NEVER WD-40 -KEEP THE TIPS CLEAN AND SERRATIONS CLEAR |
|
|
HURST EXTENSION RAMS
MODEL 30A |
35LB
RAM CLOSED 23IN RAM OPEN 36IN OPENING FORCE 15,710 CLOSING FORCE 6120LB |
|
|
HURST EXTENSION RAMS
MODEL 60 A |
WEIGHS 59LBS
RAM CLOSED - 35IN RAM OPEN-64IN OPENING FORCE 15,710 CLOSING FORCE 6120 |
|
|
MAINTENANCE OF THE RAMS
|
BOTH UNITS ARE EASILY MAINTAINED BY KEEPING THEM CLEAN, KEEPING THE TEETH ON THE UNITS CLEAR AND FREE FROM BURRS
-COUPLINGS HAVE TOBE KEPT FREE OF DIRT AND GRIME -THE UNIT IS TESTED THE SAME WAS AS THE 32A IS |
|
|
POWER UNIT-4 CYCLE
|
MAKE-TECHUMSEH
WEIGHT-80LB HAS A RUN TIME OF APROX 3 HOURS MAKE SURE BY PASS VALVE IS IN THE CLOSED POSITION WHEN STARTING. DURING OPERATION IF TOOLS HAVE TO BE CHANGED MAKE SURE THE BY-PASS IS IN THE CLOSED POSITION BEFORE ATTEMPTING TO DISCONNECT |
