• Shuffle
    Toggle On
    Toggle Off
  • Alphabetize
    Toggle On
    Toggle Off
  • Front First
    Toggle On
    Toggle Off
  • Both Sides
    Toggle On
    Toggle Off
  • Read
    Toggle On
    Toggle Off
Reading...
Front

How to study your flashcards.

Right/Left arrow keys: Navigate between flashcards.right arrow keyleft arrow key

Up/Down arrow keys: Flip the card between the front and back.down keyup key

H key: Show hint (3rd side).h key

A key: Read text to speech.a key

image

Play button

image

Play button

image

Progress

1/27

Click to flip

27 Cards in this Set

  • Front
  • Back
Which two components, at the Circulating Water Screenhouse, function to prevent debris from entering the CWP suction? A. bar grill / traveling screensB. Weir / traveling screensC. trash rack / CWS strainersD. warm water line / bar grill
A
Which system describes the secondary function of the Circulating Water System? A. Main Feedwater System.B. Condensate Storage Tank.C. Radioactive Liquid Waste discharge line.D. Chlorination System.
C
It is August, the plant is operating at 100% power, and all Circulating Water pumps running.What automatic action will occur if Circulating Water Pump 'A' trips? A. A turbine setback.B. Termination of liquid radioactive releases.C. Condenser Waterbox inlet valves go closed.D. "B" & "C" pump discharge valves close in slow speed to 25% open.
A
What is the purpose of the Circulating Water System warming line? A. Warms the Circulating Water Discharge structure to prevent cracking.B. Provides warm water to the intake of the CWSH screens to prevent "frazil ice" from forming.C. Warms certain outside tanks to prevent freezing.D. Warms the Circulating Water Pump discharge valves to prevent freezing.
B
The plant is operating at full power and STN GP-001 has been implemented.DAT0049 and DAT0050 (LP Condenser CW Inlets) indicate 32.0 and 32.5 ?F.What action should be performed? A. Manually vent the CW warming line and monitor temperatures.B. Isolate air release valves on any drained Waterboxes.C. Isolate warming line air release valve and monitor temperatures.D. Throttle 1CW002 closed 2 turns and monitor temperatures.
A
While operating at 100% a loss of power occurs to C Circulating Water and A Service Water Pumps.Which bus has lost power? A. SL-1B. SL-2C. SL-3D. SL-4
D
When is frazil ice formation most likely?When Lake temperature is 32 ?F, Air temperature is 20 ?F, and the wind is from the North at: A. 2 mph gusting to 5 mph, heavy overcast, limited ice cover.B. 15 mph gusting to 25 mph, light overcast, majority of lake ice covered.C. 15 mph gusting to 25 mph, heavy overcast, limited ice cover.D. 2 mph gusting to 5 mph, light overcast, majority of lake ice covered.
C
The plant is operating at full power and STN GP-001 has been implemented.DAT0049 and DAT0050 (LP Condenser CW Inlets) indicate 32.0 and 32.5 ?F.What action should be performed? A. Manually vent the CW warming line and monitor temperatures.B. Isolate air release valves on any drained Waterboxes.C. Isolate warming line air release valve and monitor temperatures.D. Throttle 1CW002 closed 2 turns and monitor temperatures.
A
When lake temperature is 32 degrees fahrenheit and air temperature is < 20 degrees fahrenheit, what conditions are most favorable to form Frazil ice? A. 2 mph gusting to 5 mph, heavy overcast, limited ice cover.B. 15 mph gusting to 25 mph, light overcast, majority of lake ice covered.C. 2 mph gusting to 5 mph, light overcast, majority of lake ice covered.D. 15 mph gusting to 25 mph, heavy overcast, limited ice cover.
D
What plant process CANNOT be sampled by the Secondary Sample System? A. Condensate Pump DischargeB. Individual Main Steam LinesC. Circulating Water SystemD. Low Pressure Feedwater Heater Outlet
C
The Feedwater Chemical Addition System is used for the addition of corrosion control chemicals during which operation? A. Normal operation of the Feedwater System.B. Wet lay-up operation of the Condensate System.C. Normal operation of the Steam Generators.D. Wet lay-up operation of the Steam Generators.
D
The supply tanks on the Feedwater Chemical Addition Systems are protected from overpressure by ________________. A. a relief valveB. an air operated pressure control valveC. a solenoid operated pressure control valveD. a rupture disk
A
The controls for the injection and recirculation pumps in the Feedwater Chemical Addition System are located on the __________________. A. Main Control Board next to the condensate Pump controlsB. respective sub-system's local control panelC. Corrosion Product Sampling PanelD. Condensate Demineralizer (AD) system control panel
B
During which of the following plant operating conditions is the Condensate and Feedwater Chemical Control System, Condensate Chemical Addition Sub-system used? A. Wet Lay-UpB. Normal OperationsC. CooldownD. Refueling
B
The chemical injection flow rate is controlled by _________________. A. increasing the N2 pressure in the respective supply tank.B. increasing condensate (or feedwater) flow into the respective supply tank.C. adjusting the stroke of the injection pump.D. adjusting the injection flow control valve.
C
You are walking through the Turbine Building on your way to the Control Room for Shift turnover. You have just enough time to make it and not be late. You observe a worker sitting on a large pipe in the overhead without any fall protection.Per the Wolf Creek Safety Manual, what is your responsibility? A. Contact the worker's supervisor after getting to the Control Room, then assist the worker in correcting the infraction after the turnover.B. Take note of the time, place, and if you know the worker, the worker's name and inform the Shift Manager and Safety Services after the turnover brief.C. As you walk by, shout to the worker that he needs fall protection, then continue on to the Control Room for the turnover and inform the Shift Manager.D. Immediately discuss the infraction with the employee involved and assist them in correcting the infraction, even if it means you are late for the turnover.ANSWER: D796ID: Q19665 What is the difference between red flagging with black lettering and the yellow flagging with black lettering? A. Yellow flagging warns personnel of immediate hazards that present a potential of causing injury while red flagging means personnel must obtain permission to enter prior to entry.B. The red flagging is danger flagging while the yellow means immediate hazards that present a threat of death or serious injury.C. Yellow flagging warns personnel of immediate hazards that present a threat of death or serious injury while red flagging warns personnel of immediate hazards that present a potential of causing injury.D. The red flagging is danger flagging while the yellow flagging is radiation area warning flagging.ANSWER: AAI 14-001 CONFINED SPACE ENTRY797ID: Q19667 Which contains information that is NOT part of the definition for Confined Space? A. Large enough and so configured that a person can bodily enter and perform work, and is designed for limited employee occupancy.B. Has limited or restricted means for entry or exit (tanks, pits, vessels, vaults, etc.), and may be subject to accumulation of flammable vapors, gases, toxic contaminants, oxygen deficient atmosphere and/or physical hazards.C. Has limited or restricted means for entry or exit (tanks, pits, vessels, vaults, etc.), and is designed for limited employee occupancy.D. Large enough and so configured that a person can bodily enter and perform work, and readily exceeds 1100F area temperature.
D
Who is responsible for the overall process of a confined space permit? A. Emergency Rescue TeamB. EntrantC. Entry SupervisorD. Attendant
C
A worker is required to enter and work in a confined space wearing a respirator with an air hose for air supply.What is a duty of the Attendant? A. Enter the confined space if emergency assistance is required.B. Stand outside the confined space to prevent unauthorized entry.C. Stand just inside the confined space to summon help if necessary.D. Enter the confined space with the worker and handle the air hoses to keep them from being damaged.
B
Which individual is considered responsible for pre-staging equipment at the entrance to a confined space? A. Safety ServicesB. The Confined Space SupervisorC. The AttendantD. The Entrant (worker working in the confined space)
C
According to AI 14-002, "Heat Stress And Cold Stress Management Program", what is the description of a HOT ENVIRONMENT? A. Workers in an area that the normal supply air unit is DNO tagged off and the Wet Bulb Globe Temperature is less than 850F.B. Workers in an area that the normal supply air unit is DNO tagged off and the Apparent Temperature Heat Index has reached 850F.C. Workers in an area that are dressed out in double protective clothing garments.D. Workers in an area that are dressed in protective clothing garments and the Apparent Temperature Heat Index has reached 850F.
C
AP 14B-001, Use of Plant Chemicals, covers all chemicals on site except for those chemicals used in which of the following cases? A. In "household type" cleaning in the power block.B. In a closed system isolated from the atmosphere.C. By a vendor performing contracted work on site.D. By Chemistry in the chemistry labs.
D
The NFPA (National Fire Protection Association) rates chemical from minimal to extremely hazardous. Which is the most severe rating according to NFPA? A. 1B. 3C. 2D. 4
D
Which types of accidents are covered in AP 14-002, Reporting of Accidents and Property Damage? A. Any accident or property damage to public, private or company property.B. Any onsite accidents and only damage to on site property.C. Only onsite accidents and Wolf Creek property damage.D. Any accident to public, private or company property if the employee is at fault.
A
According to AP 14-002, "Reporting of Accidents and Property Damage", if an accident occurs or property damage occurs, who shall the Control Room notify? A. the Manager of Operations (or Call Superintendent) and OSHAB. the Manager of Operations (or Call Superintendent) and Security.C. Safety Services and OSHA.D. Safety Services and Security.
D
You are involved in an accident in a company vehicle in Topeka while you were on your way to a meeting with the owners.Who should be notified per AP 14-002, Reporting of Accidents and Property Damage? A. The control room after notifying the local law authorities.B. The local law authorities and they will notify the company.C. The Owners in Topeka, then notify the local law authorities.D. Security after notifying the local law authorities.
D
The Site Operator accidently causes a grass fire in which the company vehicle is destroyed. Damage is estimated to be $3000. Per AP 14-002 "REPORTING OF ACCIDENTS AND PROPERTY DAMAGE", what type of event is this and what are the steps needed upon discovery of the event? A. Serious incident event, notify Resource Protection, notify nearest law enforcement agency, and write PIR.B. Near miss event, write an Action Report, notify Safety Services and the Control Room.C. Company property damage event, notify Call Superintendent, write Action Request, and notify Safety Services.D. Accident event, write PIR, notify Shift Supervisor, and notify Safety Services.
A
The Site Watch informs the Control Room that there is a large oil sheen visible at the Essential Service Water intake. It's coverage is about 120 square feet and estimates about two gallons visible. Per AP 14B-003, Spill and Release Reporting, the Shift Manager or designee has how many minutes to make the required notifications? A. 15B. 60C. 120D. 360E. 240 <--
B