Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
125 Cards in this Set
- Front
- Back
What is the APU accumulator pressure supposed to be at?
|
2700PSI -3100PSI
|
|
What does HIFR stand for?
|
Helicopter In-Flight Refeuling
|
|
What is the tire cut limit?
|
4/32"
|
|
How can you tell that the dehydrator kit is contaminated?
|
When less than 10% of the desiccant indicator beads are blue.
|
|
What type oil do you use on the engines and APU when it is -40 degrees C or below?
|
MIL-PRF-7808
|
|
What is the engine oil capacity?
|
7.3 US quarts
|
|
What is the APU oil capacity?
|
2.0 US Quarts
|
|
What is the main transmission oil capacity?
|
7.5 Gallons
|
|
What is the IGB oil capacity?
|
2.75 US Pints
|
|
What is the TGB oil capacity?
|
2.75 US Pints
|
|
What is the primary oil type used in the engines?
|
MIL-PRF-23699
|
|
What is the primary oil type used in the APU?
|
MIL-PRF-23699
|
|
What is the primary oil type used in the IGB and TGB?
|
DOD-PRF-85734
|
|
How long after shutdown do you have to wait before moving an aircraft?
|
20 minutes for the gyros to stop rotating
|
|
What is the NATO code for JP-5?
|
F-44
|
|
What is the NATO code for JP-4?
|
F-40
|
|
What is the NATO code for JP-8?
|
F-34
|
|
What is the publication number for the TA Deck?
|
A1-H60CA-MRC-100
|
|
What is the publication number for the Daily Deck?
|
A1-H60CA-MRC-300
|
|
What is the publication for Hand Signals?
|
NA 00-80T-113
|
|
What is the publication for Support Equipment?
|
NA-00-80T-96
|
|
What is the publication for A/C handling and security?
|
NA-00-80T-537
|
|
What publication is NATOPS?
|
A1-H60BB-NFM-000
|
|
What chapter is the NAMSOPS in?
|
Chapter 10 in the NAMP
|
|
What is the publication for A/C Fueling?
|
NA-00-80T-109
|
|
How many fire detectors are in the A/C?
|
5
2 in each engine compartment 1 in the APU compartment |
|
What is the minimum amount of fuel required to be in the A/C when landing?
|
600 lbs
|
|
At what distance is single hearing protection required at while the rotor head is turning?
|
200 ft
|
|
At what distance is single hearing protection required when APU is turning?
|
50 FT
|
|
What is the maximum amount of fasteners allowed to be popped in a row on the TGB cowling?
|
2 and no corner fasteners
|
|
What is the maximum amount of fasteners allowed to be popped in total on the TGB cowling?
|
3
|
|
What are the five steps of ORM?
|
1. Identify Hazards
2. Access Hazards 3. Make Risk Decisions 4. Implement Controls 5. Supervise |
|
What does ORM stand for?
|
Operational Risk Management
|
|
What are the 4 principles of ORM?
|
1. Make risk decisions at the right level
2. Accept risk only when the benefits outweigh the costs 3. Anticipate and manage risks 4. Accept no unecessary risks |
|
What are the three levels of ORM?
|
1. Time Critical
2. Deliberate 3. In-Depth |
|
What does NALCOMIS stand for?
|
Naval
Aviation Logistics Command Operation Management Information System |
|
How much hydraulic fluid is left when the fluid level is seen at the refill mark in the reservoir sight gauge?
|
.3 quarts
|
|
What is the limit of the piston in overfill zones on the hydraulic pump?
|
3/8"
|
|
What is the primary hydraulic fluid used?
|
MIL-PRF-83282
|
|
At what time intervals after shutdown should you read the hot side of the MGB oil level indicator versus the cold side?
|
30 minutes to 2 hours after shutdown for the hot side and 2 hours or more for the cold side
|
|
Can you service the IGB with the tail folded?
|
NO
|
|
What do you use to service the windsheild washer reservoir when it is above 32F?
|
Water
|
|
What is mixed with water for servicing the windsheild washer reservoir when it is below 32F?
|
Isopropyl Alcohol
|
|
What is mixed with water for servicing the windsheild washer reservoir when it is below 32F?
|
Isopropyl Alcohol
|
|
What is the capacity of the windshield washer reservoir?
|
1 quart
|
|
How many people are required for an A/C move?
|
6
1 PC 1 Tow Tractor Driver 1 Wing Walkers 1 Chock Walker 1 Brake Rider 1 Safety Observer |
|
How many people are required to fold the tail on an A/C?
|
5
1 person to work crackwrench 3 on the fold pole 1 safety on the stabilator |
|
What is the fuel capacity of the SH60B?
|
600 Gallons (4080 pounds)
|
|
What does NAMPSOP stand for?
|
Naval
Aviation Maintenance Publication Standard Operating Procedures |
|
What does NATOPS stand for?
|
Naval
Air Training and Operating Procedures Standardization |
|
What is the maximum towing speed of the A/C?
|
5 MPH or as fast as the slowest wingwalker
|
|
What is used to lubricate the disconnect coupling jaw teeth?
|
MIL-G-81827
|
|
What is the bomb rack called?
|
BRU-14A
Bomb Rack Unit-14A |
|
What are the bubble limits for the viscous damper?
|
Less than 1" acceptable
1"-2" should be serviced 2" > should be replaced |
|
What is the limit for the slip marks on the tail landing gear tires?
|
1/4"
|
|
What is the limit for the slip mark on the main landing gear tires?
|
There are no slip marks on the main landing gear tires
GOT YOU! YOU FUCKING IDIOT! |
|
What is the weight limit for the engine work platforms?
|
1 man, 300 lbs.
|
|
During engine priming, why does each engine get primed twice?
|
To fully prime both the direct and cross-feed fuel lines.
|
|
What must be done after return to an airfield with JP-5 available if the A/C has been fueled with an alternate fuel?
|
Drained and refilled with JP-5, or fly 3 bags of JP-5 before the A/C is unrestricted
|
|
Stop refueling operations immediately if what fails to actuate?
|
either precheck valves
|
|
What is the alternate hydraulic fluid for the SH60-B?
|
There isn't one.
GOT YOU! YOU FUCKING IDIOT! |
|
Is MIL-PRF-23699 the only type of oil which may be used when servicing the APU?
|
No, MIL-PRF-7808 is used when in temperatures of -13 degrees Fahrenheit and below
|
|
An empty engine will require how much oil?
|
7.3 quarts
|
|
What are the two different types of APUs that can be found on the SH60-B?
|
1. Parker-Hannifin Pneumatic Starter
2. Garret Pneumatic Starter |
|
What is the third step of ORM?
|
Make risk decisions
|
|
What is the second step of ORM?
|
Assess hazards
|
|
What is the fourth step of ORM?
|
Implement Controls
|
|
What is the first step of ORM?
|
Identify hazards
|
|
What pressure should the fuel servicing unit be set to?
|
55 PSI
|
|
What is the maximum internal fuel cell pressure while refueling?
|
2 PSI
|
|
How long should you wait to check engine oil after shutdown?
|
20 minutes to allow oil to drain back ino the oil tank
|
|
Where must the PC stand while directing a helicopter?
|
50 feet in front of and ten feet to the pilot's right of the helicopter
|
|
An A/C moving at 5 MPH will move how many feet in one second?
|
7.3 feet
|
|
Why must you use care when approaching ruts or dips in the ground while doing an aircraft move?
|
Tow bar may strike or damage the VHF/UHF/TACAN antenna
|
|
Based on average reaction time, an aircraft will move how many feet after an uninticipated stop signal is given?
|
6-9 Feet
|
|
What position must the stabilator be in when moving an A/C?
|
Both stabs must be folded and secured with stab struts
|
|
What must be the pressure of the sonobuoy launcher gauge before performing a DTA?
|
0 PSI (lever in dump position)
|
|
What is the limit on the blade lockpin pullers?
|
1/4 turn
|
|
Which position must the engine water wash handle on the aircraft be in?
|
Drain
|
|
What must be in place on the emergency jettison handle?
|
Shearwire
|
|
What is the minimum waveguide system pressure?
|
15 PSIG
|
|
What is the minimum amount of people required to open the doghouse?
|
2
|
|
What are the limits for the fasteners on the TGB cowling?
|
No corner fasteners.
No two fasteners popped in a row. No more than 3 at a time . |
|
What must be within 25 feet of you while taking fuel samples?
|
A Fuel Spill Kit
|
|
How many people are required to take fuel samples?
|
A minimum of two
1 to take the samples and 1 saftey observer |
|
How long after a failed or aborted APU start must you wait before trying to start again?
|
2 minutes to allow excess fuel to drain
|
|
What is the first step taken before performing a DTA?
|
Smoke a cigarette then screen the ADB
|
|
What does ADB stand for?
|
Aircraft Descrepancy Book
|
|
When checking the BIM indicators, what is the time limit for them to turn completley black?
|
10-30 seconds
|
|
What does BIM in BIM indicator stand for?
|
Blade
Indication Method |
|
How long does it take to perform a DTA?
|
As long as it takes for the PC to feel comfortable with the A/C flying
|
|
What are you looking for when inspecting fuel samples?
|
Water, debris, discolorization and microbiological growth
|
|
Who can inspect fuel samples?
|
A 310 CDI, QAR, CDQAR, Qualified Aircrew, or any Fuel Surveillance Qualified Work Center Supervisors
|
|
Who can authorize the move of an A/C with no brakes?
|
The Maintenance Officer
|
|
What is the maximum speed you are allowed to drive while towing the NC-10/108?
|
15 MPH or while driving around A/C as fast as someone can walk
|
|
To whom do you report SE misuse and abuse?
|
QA
|
|
Who can revoke an SE license?
|
The Maintenance Officer.
|
|
Who is incharge of the FOD program?
|
The Lineshack
|
|
Who monitors the FOD program?
|
Quality Assurance
|
|
According to the A1-H60CA-MRC-100, what do you nedd to check for on the Tail Bumper Skid Pad?
|
Missing paint or evidence of impact.
|
|
According to the A1-H60CA-MRC-100, what do you need to check for on the No. 1 LDS cable?
|
proper paint stripe, roll pin/safety wire for security
|
|
what does LDS in LDS cable stand for?
|
Low demand spindle
|
|
What does MSDS stand for?
|
Material
Saftey Data Sheet |
|
What does WARNING refer to?
|
any procedure or practice that, if not correctly followed, could result in injury, death, or health hazard
|
|
What does CAUTION refer to?
|
any procedure or practice that, if not correctly observed , could result in damage or destruction of equipment
|
|
what does NOTE refer to?
|
A procedure or condition that requires emphasis
|
|
What does DAMAGE refer to?
|
a harmful condition caused by an abnormal force or object
|
|
What does EVIDENCE refer to?
|
an indication of an existing condition
|
|
What does LEMA stand for?
|
Linear
Electro- Mechanical Actuator |
|
What does MAD stand for?
|
Magnetic
Anomaly Detector |
|
What does PCL stand for?
|
Pitch
Control Link |
|
What does IGB stand for?
|
Intermediate
Gear- Box |
|
What does APU stand for?
|
Auxiliary Power Unit
|
|
What hazardous material coats the inside of the AAR-47 sensors(fisheyes)?
|
Double Nickel Salt
|
|
What is the chip limit for the lens on the AAR-47 Sensor?
|
0.002 INCH
|
|
What are the LEMA to Bellcrank Clearance limits?
|
1/32 INCH- 5/32 INCH
(0.031 INCH - 0.150 INCH) |
|
Where is the Pintle Mount located and what do you need to check for on it?
|
It is located in the forward side of the cabin and you check it for cracks and security
|
|
What does CPC stand for?
|
Corrosion
Preventitive Compound |
|
What is the correct tire pressure for the Tail landing gear?
|
75-85 PSI
|
|
What is the correct tire pressure for the Main Landing Gear?
|
95-105 PSI
|
|
What is the local name for the AAR-47?
|
The Fisheye
|
|
After taking fuel samples how do you properly clean the Fuel Sample Jars?
|
You rinse out the JP-5 with an Alconox and Distilled water solution
|
|
what are the 4 things you look for on the first aid kit when inspecting it for a DTA?
|
The general condition of the first aid kit
missing or broken shearwire proper attachment inspection due date |
|
What does CRSN stand for?
|
Corrosion
|
|
What kind of towbar do we use for towing A/C?
|
A 24 Albar
|