Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
83 Cards in this Set
- Front
- Back
|
G0 (m) (L) |
Positioning at Rapid Feed |
|
|
G1 (m) (L) |
Linear interpolation |
|
|
G2 (m) (L) |
Circular interpolation clockwise |
|
|
G3 (m) (L) |
Circular interpolation counter clockwise |
|
|
G4 (m) (L) |
Dwell |
|
|
G9 (m) (L) |
Exact motion stop at intersection (non-modal, one block only) |
|
|
G10 (m) (L) |
Offset value entry through program |
|
|
G12 (m) |
Circular pocket milling cycle-clockwise |
|
|
G13 (m) |
Circular pocket milling cycle-counterclockwise |
|
|
G15 (m) |
Cartesian coordinate programming system on |
|
|
G16 (m) |
Polar coordinate program system |
|
|
G17 (m) (L) |
X/Y plane selection for arc cutting |
|
|
G18 (m) (L) |
Z/X plane selection for arc cutting |
|
|
G19 (m) (L) |
Z/Y plane selection for arc cutting |
|
|
G20 (m) (L) |
Inch unit selection |
|
|
G21 (m) (L) |
Metric unit selection |
|
|
G27 (m) (L) |
Reference position return check |
|
|
G28 (m) (L) |
Return to the primary machine Zero position (home position) |
|
|
G29 (m) (L) |
Return to reference position |
|
|
G31 (m) (L) |
Skip function |
|
|
G32 (L) |
Thread cutting (single-point or tap) |
|
|
G40 (m) (L) |
Cutter radius compensation cancel |
|
|
G41 (m) (L) |
Cutter radius compensation-left |
|
|
G42 (m) (L) |
Cutter radius compensation-right |
|
|
G43 (m) |
Tool height offset compensation-active |
|
|
G44 (m) |
Tool height offset compensation-cancel (can be G49) |
|
|
G49 (m) |
Tool height offset compensation-cancel (can be G44) |
|
|
G50 (L) |
Maximum RPM setting for constant surface Speed |
|
|
G52 (m) (L) |
Local coordinate system setting |
|
|
G53 (m) (L) |
Machine coordinate system setting |
|
|
G54 (m) (L) |
Workpiece coordinate system setting #1 |
|
|
G55 (m) (L) |
Workpiece coordinate system setting #2 |
|
|
G56 (m) (L) |
Workpiece coordinate system setting #3 |
|
|
G57 (m) (L) |
Workpiece coordinate system setting #4 |
|
|
G58 (m) (L) |
Workpiece coordinate system setting #5 |
|
|
G59 (m) (L) |
Workpiece coordinate system setting #6 |
|
|
G61 (m) (L) |
Exact motion stop at intersection (modal) |
|
|
G64 (m) (L) |
Normal cutting mode without exact stops at intersection |
|
|
G65 (m) (L) |
Custom macro call |
|
|
G70 (L) |
Finish turning/facing/bore cycle |
|
|
G71 (L) |
Rough turning/boring cycle |
|
|
G72 (L) |
Rough facing cycle |
|
|
G73 (L) |
Irregular rough turning cycle (for castings and forgings) |
|
|
G73 (m) |
Chip break peck drilling cycle |
|
|
G74 (m) |
Left hand tapping cycle |
|
|
G74 (L) |
Face groove or chip break peck drilling cycle |
|
|
G75 (L) |
OD groove chip break peck cycle |
|
|
G76 (m) |
Fine boring cycle (no tool drag marl) |
|
|
G76(L) |
Auto repetitive threading cycle (Single point) |
|
|
G80 (m) (L) |
Cancel canned cycle |
|
|
G81 (m) (L) |
Single pass drill cycle |
|
|
G82 (m) |
Single pass drill cycle with dwell |
|
|
G83 (m) |
Full retract peck drilling cycle |
|
|
G84 (m) (L) |
Tapping cycle with reversing |
|
|
G85 (m) (L) |
Boring cycle (feed in/feed out) |
|
|
G86 (m) (L) |
Boring cycle (feed in/rapid out) |
|
|
G87 (m) |
Back boring cycle |
|
|
G90 (m) (L) |
Absolute programming |
|
|
G91 (m) (L) |
Incremental programming |
|
|
G92 (m) |
Reposition origin via program |
|
|
G92 (L) |
Thread cut |
|
|
G94 (m) |
Inch or MM per Minute feed rate |
|
|
G95 (m) |
Inch or MM per revolution feed rate |
|
|
G96 (L) |
SFM value for constant surface speed |
|
|
G97 (L) |
Fixed spindle RPM/Constant Surface Speed cancel |
|
|
G98 (L) |
Inches or MM per Minute feed rate |
|
|
G99 (L) |
Inches or MM per revolution feed rate |
|
|
M00 |
Program stop |
|
|
M01 |
Optional program stop |
|
|
M02 |
Program end |
|
|
M03 |
Spindle on clockwise |
|
|
M04 |
Spindle on counterclockwise |
|
|
M05 |
Spindle off |
|
|
M06 |
Toolchange |
|
|
M08 |
Coolant on |
|
|
M09 |
Coolant off |
|
|
M10 |
Chuck, collect, or rotary table clamp |
|
|
M11 |
Chuck, collet, or rotary table unclamp |
|
|
M19 |
Orient spindle |
|
|
M30 |
Program end and return to start |
|
|
M97 |
Local sub-routine call |
|
|
M98 |
Sub-program call |
|
|
M99 |
End sub-program and return to main program |
