Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
65 Cards in this Set
- Front
- Back
|
Duties and responsibilities of CHENG? |
In charge of all engineering plants LT Brock |
|
|
Duties and responsibilities of MPA? |
Assistant to CHENG LTJG Decillis |
|
|
Duties and responsibilities of DCA? |
In charge of DC LT Spivey |
|
|
Duties and responsibilities of EOOW? |
Engineering of the watch underway Runs engineering plant |
|
|
Duties and responsibilities of EDO? |
Engineering duty officer Acts as chief engineer when CHENG and MPA are gone |
|
|
What are the 2 legal records in the engineering department? |
Engineering log Bell log |
|
|
What type of information is included in the engineering log? |
Plant status changes, maintenance casualties |
|
|
Who is the DC officer? |
CHENG |
|
|
What information is included in the daily fuel and water report? |
Ships liquid load |
|
|
What are the operating logs? |
Specific logs for individual pieces of operating machinery |
|
|
When do we jack shafts? |
To cool down or warm up bearings when ship is pulling in or out to sea |
|
|
When do we jack over main engines? |
Once a week inport |
|
|
What type of A/C units do we use aboard BURKE? |
200 ton York marine pak |
|
|
How many A/C units aboard BURKE? |
4 |
|
|
How many refrigeration units (reefers) |
2 |
|
|
How many chill water expansion tanks? |
3 |
|
|
What is the purpose of the chill water expansion tanks? |
To maintain pressure on chill water system |
|
|
What are the uses of bleed air aboard BURKE? |
Starter air Prairie air Anti icing Masker air |
|
|
How many masked emitter rings? |
3 |
|
|
What is the capacity of VCHT tanks? |
820 gallons |
|
|
What hazardous gas is the most likely to be produced by decomposing waste material in the CHT? |
Hydrogen sulfide |
|
|
What is the pressure ranges for HP Air? |
1000-3000 PSI |
|
|
How many HPACs on BURKE? |
2 |
|
|
How many LPACs on BURKE? |
3 |
|
|
Where are the LPACs located? |
#1: MER 1 #2 and #3: MER 2 |
|
|
What is the purpose of HP to LP cross connect? |
If LP air can't hold pressure HP will kick in usually at 80 PSI |
|
|
What is the purpose of the CRP system? |
Changes angle of HUB at which blades interact with water |
|
|
Why do gas turbine ships require CRP? |
We can only spin shafts in one direction |
|
|
What is the purpose of the HOPM? |
Filters. Divided the oil into control oil and power oil |
|
|
What is the purpose of the CRP head tank? |
Keeps sea water out of the ship at hub and keeps static head pressure on seal |
|
|
What is the purpose of the degaussing system? |
To counteract or neutralize magnetic field produced by the ship |
|
|
How many GTGs onboard BURKE? |
3 |
|
|
Where are the GTGs located? |
#1: AUX 1 #2: MER 2 #3: 3 GEN |
|
|
Where are the shore power receptacles located? |
Midships |
|
|
How many do we normally use to receive shore power? |
10 |
|
|
What is the GTG rated at? |
4009 amps 450 volts 3 phase 0.8 power factor 60 hz 2500kw |
|
|
What are the types of fuel used aboard BURKE? |
JP-5 F-76 |
|
|
How many fuel purifiers on BURKE? |
2 |
|
|
Where are the fuel purifiers located? |
MER 1 & 2 |
|
|
How many LM2500 engines on BURKE? |
4 |
|
|
Where are the GTMs located? |
1A & 1B: MER 1 2A & 2B: MER 2 |
|
|
What is the purpose of the engine controller? |
Provides local control of engine |
|
|
How many engine controllers on BURKE? |
4, 1 per engine |
|
|
What is the LOSCA? |
Lube oil storage conditioning Assembly Gravity feeds to the engine |
|
|
How are fires detected in the module? |
Ultraviolet sensor |
|
|
What provides cooling to MRG lube oil? |
Seawater |
|
|
What is the purpose of the Main reduction gear? |
Convert low torque high speed into high torque low speed |
|
|
Where is the waste oil holding tank located? |
AUX 2 |
|
|
Where is the plastic waste compactor located? |
Trash room |
|
|
What type of distilling plants onboard BURKE? |
Reverse osmosis |
|
|
How much water are the reverse osmosis units capable of producing per day? |
12,000 per reverse osmosis |
|
|
Where are the reverse osmosis units located? |
Mid level in MER 1 |
|
|
How many potable water tanks? |
4 |
|
|
What is the standard for water consumption per person aboard BURKE? |
36 gallons per person |
|
|
Where are the potable water pumps located? |
AUX 1 |
|
|
How many deck risers allow us to receive Potable water? |
2 |
|
|
How many sea water pumps on BURKE? |
5 |
|
|
Where are the Sea water pumps located? |
AUX 1 AUX 2 MER 1 MER 2 Shaft alley |
|
|
How many engines are online when we are in full power mode? |
4 |
|
|
How many engines are online when we are in split plant mode? |
1 engine on each shaft |
|
|
How many engines are online when we are in trail shaft mode? |
1 engine/1 shaft (other shaft spinning) |
|
|
What is cold iron? |
No engines running |
|
|
What is auxiliary steaming? |
1 generator |
|
|
Where are the hydraulic power units for steering systems located? |
Aft steering |
|
|
Where can I control steering from onboard BURKE? |
Bridge; aft steering |
