Reading...
Play button
Play button
Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
107 Cards in this Set
- Front
- Back
|
What is the FF role in truck setup for vertical ventilation ground ladders?
|
-obtain pickheaded axe
-remove ladder -carry ladder to location and position -obtain chainsaw and carry aloft for ventilation operation -cut hole |
|
|
What is the ENG role in truck setup for vertical ventilation ground ladders?
|
-secure truck
-remove and start chainsaw -remove rubbish hook -carry chainsaw and rubbish hook to ladder location and hang rubbish hook from ladder -remove start and position blower -remove and position secondary ladder for egress -start PPV after hole is cut |
|
|
What is the FF role in truck setup for aerial setup?
|
-obtain pickheaded axe
-remove capt side wheel chocks and place -remove and place capt side stabilizer pads -remove jack pins and place at highest hole possible -secure equipment and take to the turntable -lift cover on aerial control pedestal and depress emergency stop button identify overhaed obstructions in operational area |
|
|
What is the ENG role in truck setup for aerial setup?
|
-set parking brake and front wheel lock
-engage aerial master and aerial pto -proceed to stabilizer control panel; deploy stabilizers and level truck within safe operating limits -perform 360 on truck ensure pins are properly placed and chocks are properly placed -proceed to pedestal and secure chain -identify overhead obstructions and make sure crew is aware -release emerstop and return power to ladder |
|
|
What is the FF role in truck setup for auto extrication setup?
|
-remove tool staging tarp
-open all 3 covers on front bumper, activate AMKUS power rocker switch in the middle -pull all 3 lines to extrication/work area, enough to work around entire area and place on tarp -assist engineer in connecting tools -operate tools as directed by captain |
|
|
What is the ENG role in truck setup for auto extrication setup?
|
-set parking brake and front wheel lock (chocks if on steep grade)
-activate PTO and place transmission in drive to power AMKUS system -remove spreaders and cutter and place tools on staging tarp -connect tools to hydraulic lines and ensure secure connection -activate red and blue switches on control unit, ensure both are working properly -operate tool as directed by captain |
|
|
What should be in place and ready to go prior to starting extrication?
|
charged hose line (F500 should be used if any flammable liquids are present)
|
|
|
When are seat belts not required?
|
only when attending to a patient in the patient compartment of the ambulance (otherwise seat belts before apparatus is moved are required)
|
|
|
What is the service life of 800mhz batteries?
|
18mo
|
|
|
Can hose be loaded wet or dirty?
|
synthetic hose wet yes, all hose dirty no
|
|
|
What should dirty hose be washed with?
|
water only
|
|
|
When should foam be flushed from hose?
|
immediately after use
|
|
|
What type of roll should dry hose be placed in when in hose racks?
|
loosely rolled (donut rolled)
|
|
|
How often should hose be removed from apparatus and inspected for physical damage to the fabric, coupling threads, and deterioration of the gaskets?
|
quarterly
|
|
|
Hose couplings should be inspected for damaged threads, corrosion, out of round, swivel not rotating freely, slippage on the hose, missing lugs, other defects that impair operation when?
|
after each use, at each service test of the hose
|
|
|
Soft suctions and uncolored by-passes shall be scrubbed clean with soap and water and inspected when?
|
semi-annually in April and October
|
|
|
When is hose tested and at what pressure for how long?
|
once a year, in September, at 250psi for five mins
|
|
|
What type of hose is tested one length at a time?
|
hose that has been repaired or recoupled
|
|
|
All 4inch hose shall be service tested with what between the pressure source and the 4inch hose being tested?
|
a length of 2-1/2
|
|
|
Where should personnel be when inspecting for leaks during hose testing?
|
15' to the left side of the nearest hose line in the test layout (the left side is the side which is to the left when facing the free end from the pressure source)
|
|
|
When marking hose what does the top and bottom number represent?
|
top is year placed in service, bottom is sequence number
|
|
|
All 2-1/2" hose will be surveyed after how many years of service?
|
15
|
|
|
All 1-1/2 and 1-3/4 double jacket hose will be surveyed after how many years of service?
|
10
|
|
|
All 4" hose will be surveyed after how many years in service?
|
10
|
|
|
In multistory fire, unless otherwise told to do so where should engineers remain?
|
near their apparatus
|
|
|
In order to preserve pumpers officers of secondary arriving companies at fires observing the necessity to lay a line shall whenever practical lay to or from what engine?
|
the engine already working the fire
|
|
|
The goal of the El Cajon Fire Department is to operate vehicles in a manner that will not jeopardize the safety of the public, nor the well being of members of the Department riding in the vehicles. When operating fire department vehicles each member shall adhere to which laws?
|
federal, state, local laws as well as el cajon fire department procedures which apply to the operation of motor vehicles
|
|
|
When is the Emergency Stop PTO Bypass used on truck?
|
when the aerial ladder and/or stabilizers need to be operated but the Emergency Stop button on the aerial platform is engaged
|
|
|
Where are the Emergency Stops located on the truck?
|
on the aerial platform, the pedestal, and within the lower control station at the rear of truck 6
|
|
|
What is the sequence to move the ladder if the Emergency Stop button is depressed on the aerial platform?
|
-open the compartment at the base of the ladder (alarm will sound)
-hold down the deadman switch"Emergency Stop PTO Bypass" -use either manual controls, or have another firefighter use the stabilizer manual controls depending which needs to be operated |
|
|
Which controls operate when the Emergency Stop Bypass is used on the truck?
|
manual only
|
|
|
What can be used to move the truck stabilizers in cases such as having lost firm on ground or if the slope/grade of the truck exceeds and angle greater than 8 degrees?
|
the stabilizer override
|
|
|
How can you operate on the short jacked side or raise the aerial out of the cradle without the stabilizers firm on ground?
|
the stabilizer override
|
|
|
Is the command zone on the truck working with stabilizer override?
|
no
|
|
|
The aerial ladder on the truck should always be bedded using the "Auto Align" feature at approximately what psi for stability when driving?
|
2800-3300psi (this is obtained when all four outriggers are fully extended and firm on ground, when tilting the cab it is recommended that the outriggers are fully extended and firm on ground)
|
|
|
What is the emergency power unit (EPU) on the truck?
|
a 12-volt starter motor that powers a small pump and utilizes the existing hydraulic lines on Truck 6
|
|
|
When would you use the EPU on the truck?
|
-the Aerial PTO is out of service but there is still electrical power (Aerial Master)[in this case the command zone is still working aerial pedestal and yellow stabilizer controls still working]
-if both the Aerial Master and Aerial PTO are out of service(command zone is oos)[aerial pedestal controls and yellow stabilizer controls are oos. the manual controls must be used along with the EPU] |
|
|
When sitting in the cab on truck 6 how can you tell that the generator is on correctly from looking at the ladder platform?
|
the guiding lights at the bottom will be lit
|
|
|
When shutting down the generator on truck 6 what is the first thing that needs to be done?
|
turn on the main breaker first (so that the generator is not shut down while it is under an electrical load)
|
|
|
When placing the truck transmission into neutral when shutting down the generator if the display shows a flashing "N" what does that mean?
|
the throttle shutdown was not engaged and the transmission will not change gears. engage the throttle shutdown and make sure the "N" is steady
|
|
|
The command lights on the truck should not be stop in extreme wind conditions, they are tested to a max of how many mph?
|
55mph
|
|
|
How high do the command lights stand?
|
7' 4"
|
|
|
About how much slack should you want on the amkus reel?
|
15'
|
|
|
When engaging throttle shutdown in the cab of truck how long should you allow for low idle?
|
5sec
|
|
|
What do you do for accidents involving city property vs non city property with injury or damage?
|
law enforcement will fill out a "collision report", responsible employee completes city of el cajon vehicle accident report and forward through chain of command to city manager
|
|
|
What do you do for accidents involving only city property non injury?
|
responsible employee forward a city of el cajon vehicle accident report and forward through chain of command to city manager, if more documentation is necessary officer may choose to contact police for collision report
|
|
|
What do you do for vehicle accident with no property damager?
|
responsible party will complete a report of accident/incident/facility damage form and through the chain of command forward it to the city managers office for review
|
|
|
Whenever city equipment is involved in an accident in which there is damage to private property or where personal injuries are sustained who is notified immediately?
|
law enforcement
|
|
|
The employee involved must remain at scene until law enforcement gathers proper report. If a citizen requests information regarding accident refer them where?
|
city manager's office
|
|
|
When must report be submitted by the responsible party?
|
before leaving duty
|
|
|
When apparatus is stopped in hazardous positions on streets or roadways what shall be displayed to warn traffic of danger?
|
warning lights
|
|
|
Which California Vehicle Code provides drivers of authorized emergency vehicles with exemptions from complying from selected sections of the Vehicle Code during specified conditions when the vehicle is being driven in response to an emergency call?
|
Section 21055
|
|
|
Does the Vehicle Code provide full protection against liability when those vehicles must violate traffic laws during emergency situations?
|
no, provides limited liability as long as the operator drives with "due regard" for safety
|
|
|
Emergency warning devices shall not be used on freeways with the exception of what?
|
flashing amber to rear. units on scene shall utilize all emergency code 3 lighting
|
|
|
In response to emergencies apparatus shall not pass each other unless what?
|
one is disabled or delayed and company officer has clearance over the radio before passing
|
|
|
If a fire is encountered while enroute responding to an alarm what should be done?
|
if no other department apparatus is present the officer shall notify dispatch immediately and proceed to extinguish the fire encountered
|
|
|
Who's responsibility is it to use a backer at all times?
|
the driver operator
|
|
|
Who's responsibility is it for safe backing maneuvers?
|
apparatus operator
|
|
|
If involved in a minor traffic collision with no injury while responding to an emergency what should happen?
|
notify dispatch, leave a crew member at accident, continue response to emergency and request additional resources if necessary
|
|
|
Any information regarding accident involving city owned automobiles or personal automobiles driven by city employees on official city business shall be released only to investigators from where?
|
the fire department, police department, or city manager's office. if unsure request i.d.
|
|
|
Who is staffed 24hours and has keys to open fire control/security office and mall entrances at parkway plaza?
|
mall security
|
|
|
What houses the alarm panel, smoke removal controls, system maps, public announcement system, and a mall telephone system at parkway plaza?
|
the fire control/security office (in addition a plastic covered plaza map is available for fire personnel)
|
|
|
How many exhaust fans in the smoke removal system at parkway plaza?
|
12, located in the common area outside the individual occupancies(activated when smoke is detected in the mall)
|
|
|
If the smoke is not in the common area of parkway plaza how can it be directed to turn on smoke removal system?
|
into the common area, and activating the ventilation fans from smoke remove controls in the fire control/security office
|
|
|
The fire protection system in parkway plaza consists of sprinkler and standpipes. These are interconnected and supplied through how many risers and how many post indicator valves?
|
15risers, 12 post indicator valves
|
|
|
Where are the risers found in parkway plaza?
|
the rooms accessed through the exterior delivery alleys. the post indicator valves are labeled with riser identification numbers that each one supplies
|
|
|
Where are fire department connections located in parkway plaza?
|
near each post indicator valve
|
|
|
The standpipe portion of the system in parkway plaza (identified on plaza map) has how many 2-1/2" standpipe connections for fire department use?
|
13, located strategically throughout he mall
|
|
|
What does the first arriving company do in parkway plaza fire?
|
access the emergency through the nearest entrance. the first arriving engine company will investigate and determine the course of action
|
|
|
What will the second arriving company do in parkway plaza fire?
|
company officer respond to the fire control/security room and access the fire alarm panel and smoke removal system. the remaining fire personnel will remain mobile at their engine and prepare for the assignment of pumping into the appropriate FDC
|
|
|
What will the third arriving company do in parkway plaza fire?
|
go to the staging (identified by first arriving company) area and prepare to assist supplying hose and equipment
|
|
|
What will the remainder of the first alarm including truck, rescue, medic do?
|
report to staging and await assignment
|
|
|
How many lanes should be kept open on a traffic collision?
|
as many as safely possible
|
|
|
First arriving engine or truck on roadway response should always positioned how?
|
to protect the scene
-should provide work area protected form traffic approaching in at least one fire station -apparatus angle on roadway should block to create a barrier between scene and approaching traffic -apparatus placent should slow and redirect traffic -use fire apparatus to block at least one additional traffic lane more than already obstructed by the vehicle collision if possible -when practical protect pump panel |
|
|
EMS units, equipment and patents should be kept within what created by the blocking apparatus at all times?
|
the "shadow"
|
|
|
At all intersections or where the incident may be near the middle lane of the roadway what needs to be protected?
|
two or more sides
-use police vehicles to expand initial safe work area for traffic approaching from opposite directions -blocking of the work area must be prioritized from the most critical or highest traffic volume to the least critical traffic direction -for first arriving engine company where hose line may be needed block so the the pump panel is "downstream" on the opposite side of oncoming traffic |
|
|
What is upstream and downstream traffic travel?
|
upstream is where the traffic is coming from, downstream is where it is going
|
|
|
What is the shadow of the blocking apparatus?
|
the protected work area at the vehicle related roadway incident that is shielded by the block from apparatus and other emergency vehicles
|
|
|
What are the three types of aircraft emergencies?
|
fires(aircraft is located on the ground), standbys(could be fire or other malfunction, but aircraft is still in air), crashes(while taking off, taxiing, or landing)
|
|
|
On air field incidents units shall remain in their predesignated staging areas and shall respond only to the direction of whom?
|
the fire department incident commander after said officer receives instructions and clearance from the gillespie field control tower. in the absence of IC access at the direction of the control tower
|
|
|
Positive control on the runway will be provided by either radio communications or what?
|
light signals to specific vehicles
|
|
|
Does gillespie control tower monitor heartland radio frequency?
|
no, except during daily radio tests and aircraft emergencies
|
|
|
From Gillespie Field Control Tower what are the Different Light Signals?
|
- Flashing Green or Steady Green = Cleared
-Steady Red = Stop -Flashing Red = Clear the Runway -Flashing White = Return to Station -Alternating Red and Green = General Warning/Caution |
|
|
Where is the primary staging area at gillespie field?
|
-Suppression Units - El Cajon Flying Service. 1835 N Marshal Ave, stage prior to the taxiway
|
|
|
Where is standby area A at gillespie field?
|
west end of the field at intersections of tax way D and D2
|
|
|
Where is standby area B at gillespie field?
|
central area of the field at the intersections of taxiways D and A
|
|
|
Where is standby area C at gillespie field?
|
east end of gillespie field at the intersections of taxiways D and D7
|
|
|
After an earthwayake Heartland Communications Facility will initiate an Earthquake Mode and all agencies will do a roll call and a damage report within what time frame?
|
one minute
|
|
|
What is the Engineer responsibilities in earthquake mode?
|
-check to see if the Station front doors are operating
-look to see if the high voltage lines are down in front of the station, consider alternate egress if necessary, remember chain link fence will conduct electricity -remove the apparatus to a safe, outside location -obtain the street valve key (hydrant shut off) -obtain additional medical supplies (trauma pack) -portable radios and spare batteries(if available) -check the condition of the apparatus -report to the captain when your assignment is completed |
|
|
What is the Firefighter role in earthquake mode?
|
-check the overall structural safety/integrity of the station
-note any large structural cracks -note any interior doors jammed -check all utilities:natural gas, electrical power, water --shutoff only if necessary -check and start the station emergency generator if necessary -report to the captain when your assignment is complete |
|
|
Smoking is not allowed within how many feet of fueling vehicles?
|
25'
|
|
|
What about oil level shall be reported?
|
any radical change
|
|
|
Mechanical defects in apparatus or equipment shall be reported to the Company Officer when?
|
immediately upon discovery
|
|
|
How often are batteries checked?
|
weekly (daily)
|
|
|
The proper use and retention of chock blocks carried on apparatus shall be the sole responsibility of whom?
|
engineer or acting engineer operating the apparatus
|
|
|
When is the pumper tank flushed?
|
twice yearly, april and october (drain tank, flush inside of tank with water and drain it, fill tank and check for prime)
|
|
|
When doing the draft drill the strainer end of the suction shall be kept at least how many inches from the bottom of the reservoir and how man inches or more below the surface of the water?
|
12 inches from the bottom of the reservoir and 24 inches or more below the surface of the water (ear protection must be worn)
|
|
|
How often are apparatus detailed?
|
-apparatus :as needed
-ambulance: as needed -staff vehicles: quarterly (interior/exterior detail shall begin january 1 and end december 31st |
|
|
When apparatus is how many miles from service a work order is done?
|
200
|
|
|
For staff cars service is due when?
|
every 4000 miles or six months whichever comes first
|
|
|
Service for ambulances, engines, and truck is due when?
|
every 3000 miles or six months whichever comes first
|
|
|
When is the floor test performed on 1998&2001 KME?
|
weekly (voltmeter 12-14.5v, tachometer 600rpm, oil at idle 15-60psi, water shouldn't exceed 220F, transmission oil temp shouldn't exceed 250psi)
|
|
|
When is the dry vacuum test (relief valve[test to 150psi], discharge gauge, high pressure pump[increase to 265psi], bleeder drain valve[let master drain for 10sec all others for 15] performed on 1998&2001 KME?
|
first week of each Month (prime no longer than 30-45sec with two minute cooling period, vacuum of 20inches shouldn't drop more than 10psi in 10min)
|
|
|
When is the floor test performed on 1990 Pierce?
|
weekly (voltmeter 12-15v, tachometer 600rpm, oil at idle 1-10psi, water shouldn't exceed 210F, increase to 1,000rpm)
|
|
|
When is the dry vacuum test (relief valve[test to 150psi], discharge gauge[transmission oil pressure should read 20psi at 1250 rpm], bleeder drain valve[let master drain for 10sec all others for 15] performed on 1990 Pierce?
|
first week of each Month (prime no longer than 45sec, vacuum of 20inches shouldn't drop more than 10psi in 10min)
|
|
|
When should apparatus be inventoried and where should the sheet be kept?
|
daily, kept on the apparatus (missing inventory is work ordered)
|
|
|
If apparatus is muddy when should it be washed?
|
before the end of the shift
|
