Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
394 Cards in this Set
- Front
- Back
What is the primary duty of crash and salvage? |
To save lives |
|
What is the function of rescue teams? |
To effect rescue personnel from burning or crashed aircraft |
|
Which access point provided the most effective and expeditious entry to an aircraft? |
Normal access doors |
|
Can you jettison a canopy with fuel in the cockpit? |
No |
|
When can you excercise emergency entry into an aircraft ? |
If structural or other damage normal access cannot be made |
|
When using a power saw, how do you cut the fuselage to gain entry into an aircraft? |
Cut at least 2 inches from ribs |
|
What is the flashpoint of jp-4? |
-40 degrees |
|
What is the spread rate of Jp-4? |
700-800 feet per minute |
|
What grade is JP-5? |
Kerosene |
|
What is the most effective method for stopping an oxygen leak? |
Spray leak with water fog |
|
What is another name for overheated battery? |
Thermal runaway |
|
How do you combat an overheated battery that has flames present? |
Use Halon 1211 or CO2 |
|
What size halon bottles are accepted on the flight line? |
150 pounds |
|
On the airfield, who gives annual training on all firefighting extinguishers? |
Fire department |
|
When should airfield firefighting extinguishers be inspected? |
Daily |
|
What agent should you not use on a class d fire? |
Halon 1211 |
|
How do you clean dirt and soot off proximity suits? |
Sponge off with mild soap and water |
|
How do you clean grease stains off proximity suits? |
Remove with dry cleaning solvents |
|
How much water is in the CF 4000L Amertek? |
1050 gallons |
|
How much is in the foam tank of the CF4000L Amertek? |
156 gallons |
|
What is the discharge rate of the CF4000L Amertek roof turret? |
500 GPM |
|
What is the discharge rate of the CF4000L Amertek bumper turret? |
250 GPM |
|
How many hand lines are on the CF 4000L Amertek? |
2 (100ft) |
|
How much halon is available on one hand line on the CF 4000L Amertek? |
5000 |
|
How much water can a p-15 hold? |
6200 |
|
How much can be held in the foam tank of the p-15? |
515 gallons |
|
At what temperature do fusible plugs deflate? |
400 degrees |
|
Who is responsible for organizing supervising and training the crash and salvage, and rescue team? |
Air Bosn |
|
On a cv/can what is the minimum amount of proximity suits in each hangar bay should be available? |
2 |
|
What sound-powered circuit is used for afff station? |
X50-J |
|
During a fire, what must personnel have on order to enter enclosed fuel stations ? |
SCBA |
|
What is the lifting capacity of a crash forklift? |
20000 |
|
What consists of initial equipment on scene during aircraft firefighting? |
P-25 and 4 hose teams |
|
How are most ejection seats used in the navy fired? |
Pulling down on the face curtain |
|
How long ordnance cooling should be conducted? |
Min of 15 minutes |
|
What parts make up a standard screw driver? |
The handle , the shank , and the end |
|
What tool is manufactured with straight serrated jaws for gripping objects? |
Combination jaw pliers |
|
What is the crescent adjustable wrench often referred to as? |
Knuckle buster |
|
What is the name of the most common adjustable pipe wrench? |
Stillson |
|
What hammer is most used by ABH? |
Ball peen |
|
What tools are designed for prying boards from crates, pulling spikes or heavy nails and as a lever for moving heavy objects short distance? |
Wrecking bars |
|
What are the most common used torque wrenches? |
Micrometer setting Dial indicating Deflecting beam |
|
What tool is known As the jitterbug? |
Rotary impact scaler |
|
What tool is used in conjunction with the rotary scaler? |
Needle impact scaler |
|
What are the two types of portable sanders? |
Pneumatic and electric |
|
What is the simplest and most common measuring tool? |
Steel rule |
|
What tool is usually referred to as a come-along ? |
Chain ratchet |
|
Bolt cutters are made in the length of how many inches? |
18-36 inches |
|
The amphibious assault ship crash crane Is capable of lifting a max of how many pounds? |
70,000 |
|
What is the primary source of dc power for the AACC? |
Two 12 v batteries |
|
What is the length of the boom on the AACC? |
46ft |
|
The wire rope should be replaced when there is more then how many broken wires in one lay of rope ? |
One |
|
Crash and salvage units should maintain a total of how many fabric hoisting strings ? |
8 |
|
Safe working load limit is what percentage of the breaking strength of new nylon tape? |
50 % |
|
Fatigue of a wire rope sling can be recognized by which of the following characteristics? |
The outer wire is broken |
|
In the air terminal, personnel assignments are made by what official? |
CPO |
|
An aircraft director should assume what positions when directing and aircraft? |
Where eye contact is made with pilot |
|
An aircraft being taxied on land with 25ft of obstruction must have how many safety instructors? |
2 |
|
As a minimum, two crews are composed of how many personnel? |
6 |
|
Before towing an aircraft, the director should make sure what are installed? |
Ground safety locks |
|
What condition will determine how an aircraft should be secured ? |
Weather |
|
As a minimum, two crews are composed of how many personnel? |
6 |
|
What condition will determine how an aircraft should be secured ? |
Weather |
|
What official is responsible for providing fire extinguishing equipment to the flight line? |
Fire station chief |
|
On an aircraft carrier, who is overall supervisor of the flight deck ? |
Flight deck chief |
|
Who conducts the pressing briefings for plane directors? |
Flight deck chief |
|
Who makes final decision on which aircraft will make the schedule launch? |
ACHO |
|
Why are aircraft pointed onto the wind prior to starting? |
To help prevent hot starts |
|
A briefing of specific launch procedures and sequences are giving by what officer? |
ACHO |
|
Which of the the vehicles shall not be used as a intermediate response vehicle? |
p-15 |
|
Category one aircraft crash crane should arrive at the scene mishap within a max of how many mins? |
15 minutes |
|
What is the minimum number of firefighters used to affect a rescue? |
2 |
|
On station, what documents should identify staging areas and water supply? |
Grid maps |
|
What is the minimum number of tag lines required for salvage organizations ? |
4 |
|
Which of the the vehicles shall not be used as a intermediate response vehicle? |
p-15 |
|
What is the minimum number of firefighters used to affect a rescue? |
2 |
|
On station, what documents should identify staging areas and water supply? |
Grid maps |
|
What is the minimum number of tag lines required for salvage organizations ? |
4 |
|
The new E-28 arresting tape used for slings has a max breaking strength of how many pounds? |
150,000 |
|
New nylon tapes should be replaced at what intervals? |
6 years |
|
Used nylon tapes should be replaced at what intervals? |
3 years |
|
A nylon tape should be replaced when it received a cut of at least how many inches ? |
1/4 inch |
|
What official is responsible for making sure quality workmanship is attained? |
Work center supervisor |
|
Corrosion that occurs when two different metals are connected and exposed to salt water is known as? |
Galvanic |
|
With which types of corrosion is the ABH mainly concerned? |
Galvanic and surface |
|
What is the primary purpose of any paint finish on the navy? |
Protection of exposed surface |
|
Nonskid materials in the federal supply system are assigned a nonexpendable shelf life of how many months ? |
12 months |
|
Non-skid materials in the federal supply systems are assigned a nonexpendable shelf life....how many months is this shelf life ? |
12 months |
|
At what range, in the degrees Fahrenheit, should nonskid coatings be stored until used? |
55-100 degrees |
|
The roller chain should be adjusted for what maximum amount of play? |
1/4 inch |
|
On the e-5 dual straight pendent, the arresting cables are spaced how many feet apart? |
30 ft |
|
Arresting gear cable should be a minimum of how many inches ? |
2 |
|
Arresting gear cable should be a minimum of how many inches ? |
2 |
|
How many different size ALBARS are require ? |
4 |
|
Arresting gear cable should be a minimum of how many inches ? |
2 |
|
How many different size ALBARS are require ? |
4 |
|
Weight of the p25 fully loaded ? |
18850 pounds |
|
Weight of the p-25 unloaded? |
12050 pounds |
|
Weight of the p-25 unloaded? |
12050 pounds |
|
How many different turrets are on the p-25 and what are they |
4(0, 150, 250, 500) |
|
Weight of the p-25 unloaded? |
12050 pounds |
|
How many different turrets are on the p-25 and what are they |
4(0, 150, 250, 500) |
|
What kind of tired does the p-25 have? |
Permafoam |
|
How many halon bottles are on the p-25 and where are they located? |
3 bottles behind senior suitman |
|
What is the normal operating RPM on the p-25? |
2750 RPM |
|
What is the idle RPM on the P-25? |
800RPM |
|
What is the idle RPM on the P-25? |
800RPM |
|
What is the color of the 6 inch band on the CO2 bottle? |
Yellow |
|
What is the idle RPM on the P-25? |
800RPM |
|
What is the color of the 6 inch band on the CO2 bottle? |
Yellow |
|
How many pounds should the forklift boom adapter be tested to? |
5714 |
|
If the platform passed the load test , the platform must be certified at how many pounds? |
1000 |
|
If the platform passed the load test , the platform must be certified at how many pounds? |
1000 |
|
Where PKP should be directed? |
At the base of the flame in a sweeping motion |
|
If the platform passed the load test , the platform must be certified at how many pounds? |
1000 |
|
Where PKP should be directed? |
At the base of the flame in a sweeping motion |
|
What is the effective range of an 18 lb PKP exstinguisher? |
18-20 ft |
|
For what class of fire is PKP more effective ? |
Bravo |
|
How would you protect yourself from the intense heat of fire with PKP? |
Short burst in air served as a heat shield |
|
What activates Halon release? |
CO2 |
|
The halon system takes approximately how long to completely discharge? |
10 seconds |
|
Can AFFF be used on a class Alpha fire? |
Yes because of the cooling effect of water |
|
Can AFFF be used on a class Alpha fire? |
Yes because of the cooling effect of water |
|
What class of fire is AFFF normally used for? |
BRAVO |
|
What is the best method to remove non skid? |
Abrasive blasting |
|
Non skid epoxy primers may be applied by what method? |
Roller coasting |
|
A slip resistant surface is required for flight deck and hangar deck on a carrier, which nonskid system is intended for this use? |
Composition G |
|
A slip resistant surface is required for flight deck and hangar deck on a carrier, which nonskid system is intended for this use? |
Composition G |
|
At what temperature will cause expoxy binders to ignite or decompose? |
752 degrees |
|
Rubber tires will burn at what temperature? |
500-600 degrees |
|
The TD-1A adjust from? |
1.5ft -9ft 10 inches |
|
TD-1A weighs how much? |
12pounds |
|
The TD-1A has a safe working load of ? |
10,000 pounds |
|
The TD-1A has a safe working load of ? |
10,000 pounds |
|
What is the maximum aircraft weight the E/28 arresting gear can handle? |
78,000 pounds |
|
The TD-1A has a safe working load of ? |
10,000 pounds |
|
What is the maximum aircraft weight the E/28 arresting gear can handle? |
78,000 pounds |
|
What is the maximum aircraft engaging speed of the E/28 arresting gear? |
160 knots |
|
The TD-1A has a safe working load of ? |
10,000 pounds |
|
What is the maximum aircraft weight the E/28 arresting gear can handle? |
78,000 pounds |
|
What is the maximum aircraft engaging speed of the E/28 arresting gear? |
160 knots |
|
Liquid oxygen boils into gaseous oxygen at what temperature? |
-297 degrees |
|
What is the expansion ration of liquid oxygen? |
860 to 1 |
|
Anti-icing fluids usually have a mixture of what % alcohol and what % glycerin? |
85% alcohol and 15 % glycerin |
|
Anti-icing fluids usually have a mixture of what % alcohol and what % glycerin? |
85% alcohol and 15 % glycerin |
|
What is the flash point of JP-5? |
100 feet per minute |
|
What is the flash point of JP-5? |
140 degrees |
|
What is the flame spread of JP-5 |
100 feet per minute |
|
What is the flame spread of JP-5 |
100 feet per minute |
|
How many aircraft fabric hoisting slings are crash and salvage required to maintain? |
8 |
|
What are the markings on the elevator? |
6 inch wide 12 inch long alternating red and yellow segments |
|
What are the markings on the elevator? |
6 inch wide 12 inch long alternating red and yellow segments |
|
What is the rated capacity of the tail hook dolly? |
400 pounds |
|
What are the markings on the elevator? |
6 inch wide 12 inch long alternating red and yellow segments |
|
What is the rated capacity of the tail hook dolly? |
400 pounds |
|
What manual is the NAPTOPS US Navy aircraft firefighting and rescue manual? |
NAVAIR 00-80R-14 |
|
What are the markings on the elevator? |
6 inch wide 12 inch long alternating red and yellow segments |
|
What is the rated capacity of the tail hook dolly? |
400 pounds |
|
What manual is the NAPTOPS US Navy aircraft firefighting and rescue manual? |
NAVAIR 00-80R-14 |
|
What manual is the NAPTOPS US Navy aircraft emergency rescue information manual? |
NAVAIR 00-80R-14-1 |
|
How should a wheel assembly fire be exstinguished? |
Halon 1211/water fog in large volumes |
|
How should a wheel assembly fire be exstinguished? |
Halon 1211/water fog in large volumes |
|
How long does it take to open ballistic doors? |
28 seconds |
|
What are the dimensions of the AFFF handline on the P-25? |
100 ft long 1-1/2 inch hose |
|
What are the dimensions of the AFFF handline on the P-25? |
100 ft long 1-1/2 inch hose |
|
Who is ultimately responsible for the FOD program? |
The commanding officer |
|
Who has overall responsibility for the integrity watch aboard the ship? |
Air officer |
|
Who has overall responsibility for the integrity watch aboard the ship? |
Air officer |
|
What is the flash point of JP-8 jet fuel? |
100 degrees |
|
Who has overall responsibility for the integrity watch aboard the ship? |
Air officer |
|
What is the flash point of JP-8 jet fuel? |
100 degrees |
|
What is the spread rate of JP-8? |
100 feet per minute |
|
Who has overall responsibility for the integrity watch aboard the ship? |
Air officer |
|
What is the flash point of JP-8 jet fuel? |
100 degrees |
|
What is the spread rate of JP-8? |
100 feet per minute |
|
How many pounds of Halon 1211 are contained in the Halon 1211 portable fire exstinguisher? |
20 pounds |
|
What portable CO2 exstinguisher sate available for use aboard aircraft carriers? |
15 pound capacity exstinguishers |
|
What portable CO2 exstinguisher sate available for use aboard aircraft carriers? |
15 pound capacity exstinguishers |
|
How many hoses are on the T-3000 fire truck? |
2 |
|
What is the most satisfactory tool for cutting acrylic plastic? |
Couture blade |
|
What is the most satisfactory tool for forcible entry into fuselage areas? |
The power saw equipped with metal-cutting blades |
|
Who uses a white stubby wand on a CVN? |
Hook up petty officer. JBD SAFTEY and Center deck operator |
|
What is the catapults officer primary function? |
Final inspector only |
|
Who must give permission to use the defeat interlock mode of the catapults? |
CO |
|
Who gives the signal to the topside petty officer to initiate hook up for launch? |
Landing officer |
|
Who gives the signal to the topside petty officer to initiate hook up for launch? |
Landing officer |
|
What is considered a hang fire? |
If catapult does not fire within 10 seconds |
|
How many loads must be fired after a hang fire on the catapults? |
2 |
|
How many loads must be fired after a hang fire on the catapults? |
2 |
|
TD assembly when properly installed, working capacity is? |
10,000 pounds |
|
How many loads must be fired after a hang fire on the catapults? |
2 |
|
TD assembly when properly installed, working capacity is? |
10,000 pounds |
|
TD when improperly installed, working load is? |
6,000 pounds |
|
Who must inspects and certify the arresting gear before used? |
Naval Air Warfare Center |
|
What manual can you find information on arresting gear? |
NAVAIR 51-5-28 |
|
What is bird caging? |
Opening of strands on the cable |
|
What is the max weight that a E-28 can accommodate? |
78,000 pounds |
|
What is the max weight that a E-28 can accommodate? |
78,000 pounds |
|
What is the cycle time for the E-28 ? |
80 seconds |
|
How many broken wires are allowed on the E-28 gear? |
9 |
|
What is the manual for the E-28 arresting gear? |
NAVAIR 51-5-31 |
|
What is the manual for the E-28 arresting gear? |
NAVAIR 51-5-31 |
|
What pliers are designed for cutting wires? |
Diagonal pliers |
|
What is the manual for the E-28 arresting gear? |
NAVAIR 51-5-31 |
|
What pliers are designed for cutting wires? |
Diagonal pliers |
|
When using bolt cutters what are 2 types of metal you should avoid? |
Spring metal and tempered metal |
|
What is the purpose of the dynometer? |
Measure force and energy |
|
What is the purpose of the dynometer? |
Measure force and energy |
|
What is the max lifting capacity of the spotting dolly? |
16,000 pounds |
|
What is the height of the spotting dolly? |
30 inches |
|
What is the height of the spotting dolly? |
30 inches |
|
What is the draw bar pull of spotting dolly ? (A/S32-32) |
14,000 pounds |
|
What is the height of the spotting dolly? |
30 inches |
|
What is the draw bar pull of spotting dolly ? (A/S32-32) |
14,000 pounds |
|
What is the gross weight of the spotting dolly? |
11,500 pounds |
|
What is the height of the spotting dolly? |
30 inches |
|
What is the draw bar pull of spotting dolly ? (A/S32-32) |
14,000 pounds |
|
What is the gross weight of the spotting dolly? |
11,500 pounds |
|
Where is the parking break located on a TMU-70? |
In front next to handling bar |
|
When will the brake warning light illuminate on an AS32-31A? |
When oil pressure fails below 1,350 |
|
What is the gross weight of AS32-31A (flight deck )? |
12,400 pounds |
|
Up to what weight can a A/S32A-42? |
100,000 |
|
Up to what weight can a A/S32A-42? |
100,000 |
|
What is the max forward speed of the 42 shore based tractor? |
13mph |
|
How often should you clean a NWC? |
Monthly |
|
What Albar would you use to tow an FA-18 and AV-8? |
ALBAR 20 |
|
What should the deck temperature be when applying non skid? |
55-100 degrees |
|
What is the towing capacity of the A/S32-30A? |
40,000 pounds |
|
What is the towing capacity of the A/S32-30A? |
40,000 pounds |
|
What is the turning radius of the A/S-32-30A? |
142 inches |
|
What is the towing capacity of the A/S32-30A? |
40,000 pounds |
|
What is the turning radius of the A/S-32-30A? |
142 inches |
|
What is the turning radius of the A/S32-31A? |
132 inches |
|
What tool is portable metal cutting tool that can be used for cutting sheet metal, bolts, & pipes? |
Hacksaw |
|
Which wrecking bar is used for DC functions as on crash trucks on shore stations ? |
Johnson bar |
|
Which wrecking bar is used for DC functions as on crash trucks on shore stations ? |
Johnson bar |
|
What should never be used for general maintenance? |
Crash tool roll kit |
|
How many degrees are the fluke of Philips screwdriver? |
30 degrees |
|
How many degrees are the fluke of Philips screwdriver? |
30 degrees |
|
How many degrees are the flukes of the reed and prince screwdriver? |
45 degrees |
|
What is sometimes mounted to the A/S32A-31A? |
A/S47A-1GTE (Huffer) |
|
What is the name of the A/C mid range vehicle? |
A/S32A-42 |
|
What is the drawbar pull of the A/S32-42? |
10,000 |
|
What is the turning radius of the A/S32-42? |
200 inches |
|
What is the turning radius of the A/S32-42? |
200 inches |
|
What shore based tractor is used to move large, heavy shore based A/C? |
A/S32A-37 |
|
What is the turning radius of the A/S32-42? |
200 inches |
|
What shore based tractor is used to move large, heavy shore based A/C? |
A/S32A-37 |
|
What is the turning radius of the A/S32-37? |
300 inches |
|
Primer should be applied within how many hours after the metal is cleaned? |
1 hour |
|
What are the two types of non-skid? |
Abrasive and non-abrasive |
|
What is the width of the A/S32-35A? |
34 feet |
|
What is the boom length of the A/S32A-35A? |
28.5 |
|
What is the boom length of the A/S32A-35A? |
28.5 |
|
What is the ground clearance of the A/SA-35A? |
9 inches |
|
What is the boom length of the A/S32A-35A? |
28.5 |
|
What is the ground clearance of the A/SA-35A? |
9 inches |
|
What is the basic weight of the A/S32A-35A? |
133,500 pounds |
|
What is the max auxiliary main hoisting lifting capacity of the A/S32A-35A? |
10,000 |
|
What is the main hoist lifting capacity of the A/S32-35A? |
75,000 pounds |
|
What is the fuel capacity of the A/S32A-35A? |
60 gallons |
|
What is the tire pressure of the A/S32A-35A? |
38 PSI |
|
What is the travel speed of the A/S32A-35A? |
5 MPH |
|
What is the normal idle of the A/S32A-35A? |
900-1000 RPM |
|
What is the normal brake pressure A/S32A-35A ? |
65-90 PSI |
|
What manual should you refer to for information on the A/S32A-35A? |
NAVAIR 19-25G-19 |
|
What type of break system does the P-25 use? |
Dynamic Break system |
|
What type of break system does the P-25 use? |
Dynamic Break system |
|
How much water can the P -25 carry? |
750 gallons |
|
What type of break system does the P-25 use? |
Dynamic Break system |
|
How much water can the P -25 carry? |
750 gallons |
|
How much AFFF can the p-25 carry? |
60gallons |
|
What type of break system does the P-25 use? |
Dynamic Break system |
|
How much water can the P -25 carry? |
750 gallons |
|
How much AFFF can the p-25 carry? |
60gallons |
|
What is the max flow rate of the turret? |
500 GPM |
|
What type of break system does the P-25 use? |
Dynamic Break system |
|
How much water can the P -25 carry? |
750 gallons |
|
How much AFFF can the p-25 carry? |
60gallons |
|
What is the max flow rate of the turret? |
500 GPM |
|
What is the max flow rate of the handline? |
95 GPM |
|
How many heaters /what is the voltage requirement and where does it connect on P -25? |
2/ 440 VAC and the conjunction box located on the right side |
|
What powers the p-25 ? |
Detroit diesel 6V engine |
|
Where is the handline stowed on the p-25? |
Right hand side of the p-25 on a hose reel |
|
What is the diesel fuel capacity in the p-25? |
28 gallons |
|
Who authorization is needed to launch aircraft under 10 knots? |
CO |
|
What is the ejection seat for the f-18? |
Martin Baker SJU-17 |
|
What is the ejection seat for the f-18? |
Martin Baker SJU-17 |
|
What ejection seat for the AV-8? |
Stencil SJU-4A |
|
How many crash crew members are required in a CV/CVN? |
24 |
|
How many crash crew members are required in a CV/CVN? |
24 |
|
How many crash crew members are required on an amphibious ship? |
11-13 |
|
How many crash crew members are required in a CV/CVN? |
24 |
|
How many crash crew members are required on an amphibious ship? |
11-13 |
|
What is the breaking strength of E-15 hoisting sling? |
70,000 pounds |
|
What is the breaking strength of the E-27 hoisting sling? |
70,000 pounds |
|
What is the breaking strength of the E-28 hoisting sling ? |
150,000 pounds |
|
If fabric and hoisting slings are exposed to weather, what percentage are their breaking strength? |
20% |
|
How many inches must a sling be cut or torn to be replaced? |
1/4 inch |
|
What is the capacity for crash and salvage tie downs? |
10,000 pounds |
|
What is the adjustable length of the crash and salvage tiedowns? |
10-30 feet |
|
How many universal salvage harness types are there? |
3 |
|
How many aircraft tiedowns must crash crew members maintain? |
12 |
|
What navy wheel chick did the NWC4 replace? |
NWC-2 |
|
What is manila lines used for? |
Used to make up all working lines |
|
How many stabilizing lines does crash maintain? |
4 |
|
How many stabilizing lines does crash maintain? |
4 |
|
How many tag lines does crash maintain? |
4 |
|
What are the load capacity of crash and salvage tiedown straps? |
10,000 pounds |
|
What are the initial tie downs for a E-2, C-2, EA-6B, and F-18? |
6 |
|
What are the initial tie downs for a E-2, C-2, EA-6B, and F-18? |
6 |
|
What are the initial tie downs for AV-8, H-46, H-60, H-53? |
4 |
|
What are the initial tie downs for a E-2, C-2, EA-6B, and F-18? |
6 |
|
What are the initial tie downs for AV-8, H-46, H-60, H-53? |
4 |
|
What are the intermediate tie downs for E-2, C-2, EA-6B, and F-18? |
9 |
|
What are the initial tie downs for a E-2, C-2, EA-6B, and F-18? |
6 |
|
What are the initial tie downs for AV-8, H-46, H-60, H-53? |
4 |
|
What are the intermediate tie downs for E-2, C-2, EA-6B, and F-18? |
9 |
|
What are the intermediate tie down requirements for AV-8, H-46, H-53, H-60? |
6 |
|
What are the initial tie downs for a E-2, C-2, EA-6B, and F-18? |
6 |
|
What are the initial tie downs for AV-8, H-46, H-60, H-53? |
4 |
|
What are the intermediate tie downs for E-2, C-2, EA-6B, and F-18? |
9 |
|
What are the intermediate tie down requirements for AV-8, H-46, H-53, H-60? |
6 |
|
What are the permanent tie down requirements for E-2, C-2, EA-6B, and F-18? |
12/14 |
|
What are the initial tie downs for a E-2, C-2, EA-6B, and F-18? |
6 |
|
What are the initial tie downs for AV-8, H-46, H-60, H-53? |
4 |
|
What are the intermediate tie downs for E-2, C-2, EA-6B, and F-18? |
9 |
|
What are the intermediate tie down requirements for AV-8, H-46, H-53, H-60? |
6 |
|
What are the permanent tie down requirements for E-2, C-2, EA-6B, and F-18? |
12/14 |
|
What are the permanent tiedown requirements for AV-8, H-46, H-53 and H-60? |
12 |
|
What are the heavy weather tiedown requirements for E-2, C-2, EA-6B and F-18? |
18/20 |
|
What are the heavy weather tiedown requirements for E-2, C-2, EA-6B and F-18? |
18/20 |
|
What are the heavy weather tiedown requirements for AV-8, H-46, H-53, and H-60? |
16 |
|
How many hacksaw blades should crash have? |
6 |
|
How many hacksaw blades should crash have? |
6 |
|
How many v-blades should crash have? |
6 |
|
What does LOEP Stand for? |
List of effective pages |
|
What does LOEP Stand for? |
List of effective pages |
|
What does MIP stand for? |
Maintenance index page |
|
What does 3M stand for? |
Maintenance material management |
|
What does 3M stand for? |
Maintenance material management |
|
What does MRC stand for? |
Maintenance requirement card |
|
What does EGL stand for? |
Equipment guide list |
|
What does ALID stand for? |
Automated library issue document |
|
What does ALID stand for? |
Automated library issue document |
|
What does IEM stand for ? |
Inactive equipment maintenance |
|
What does ALID stand for? |
Automated library issue document |
|
What does IEM stand for ? |
Inactive equipment maintenance |
|
What does SEL stand for? |
Selective equipment list |
|
Who is overall responsible for ensuring maintenance is accomplished following 3M systems functions in the command? |
CO |
|
Who is the command 3M system manager? |
XO |
|
Who is the command 3M system manager? |
XO |
|
Who are the functional manager of the 3M system and all administrative facets of the 3M system program? |
3M system Coordinator |
|
Who is the command 3M system manager? |
XO |
|
Who are the functional manager of the 3M system and all administrative facets of the 3M system program? |
3M system Coordinator |
|
Who is the final approval of the quarterly schedule? |
Department head |
|
What request must be submitted for a LOEP change for new add-ons and for equipment removals? |
Feed back reports (FBR) |
|
Who is accountable to the department head for the proper operation of the 3m system in their department? |
DLCPO |
|
Who is accountable to the department head for the proper operation of the 3m system in their department? |
DLCPO |
|
Who helps with coordination and supervision of the departments 3M program? |
Department 3M assistant |
|
Who is accountable to the department head for the proper operation of the 3m system in their department? |
DLCPO |
|
Who helps with coordination and supervision of the departments 3M program? |
Department 3M assistant |
|
Who is responsible to the department head for the execution of maintenance within the division? |
Division officer |
|
Who is accountable to the department head for the proper operation of the 3m system in their department? |
DLCPO |
|
Who helps with coordination and supervision of the departments 3M program? |
Department 3M assistant |
|
Who is responsible to the department head for the execution of maintenance within the division? |
Division officer |
|
Who approves the weekly schedule? |
Division officer |
|
Who is accountable to the department head for the proper operation of the 3m system in their department? |
DLCPO |
|
Who helps with coordination and supervision of the departments 3M program? |
Department 3M assistant |
|
Who is responsible to the department head for the execution of maintenance within the division? |
Division officer |
|
Who approves the weekly schedule? |
Division officer |
|
Who schedules the weekly work center maintenance and supervises its proper accomplishment? |
Work center supervisor |
|
What do PMS stand for? |
Planned Maintenance System |
|
What contains relative information to PMS requirements for specific equipment which command responsible? |
PMS master file |
|
Who maintains the PMS master file? |
3M system coordinator |
|
What list provides the listing of the MIPS for systems and equipment assigned to each work center? |
LOEP |
|
What list provides the listing of the MIPS for systems and equipment assigned to each work center? |
LOEP |
|
What does SPMIG? |
Standard PMS MATERIALS IDENTIFICATION CODE |
|
What list provides the listing of the MIPS for systems and equipment assigned to each work center? |
LOEP |
|
What does SPMIG? |
Standard PMS MATERIALS IDENTIFICATION CODE |
|
The 3M system coordinator will provide a status report to the system manager how often? |
Weekly |
|
Who reviews and approve quarterly schedules? |
Division officer |
|
The work center center supervisor will use what as a daily working document for the scheduling of any maintenance actions not included on the PMS schedule? |
Current ships maintenance plan |
|
What denotes MIP issue changes included in the force revision(FR)? |
Dash (-) |
|
What denotes MIP issue changes included in the force revision(FR)? |
Dash (-) |
|
What denotes MIP additions distributed by special issue and not as part of the FR? |
Slash (/) |
|
What denotes MIP issue changes included in the force revision(FR)? |
Dash (-) |
|
What denotes MIP additions distributed by special issue and not as part of the FR? |
Slash (/) |
|
What following the periodicity code indicates a SAFTEY of a ship item? |
Asterisk (*) |
|
Aircraft hand signals |
NAVAIR 00-80T-113 |
|
Aircraft hand signals |
NAVAIR 00-80T-113 |
|
LHA/LHD NAPTOPS |
NAVAIR 00-80T-106 |
|
CVN FLIGHT/hangar deck NAPTOPS |
NAVAIR 00-80T-120 |
|
Support equipment and aircraft tow tractor |
NAVAIR 19-1-137 |