Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
58 Cards in this Set
- Front
- Back
What is the end result if a surface to be punted is not properly prepared and cleaned? |
The surface will not look it's best. The materials and valuable time are wasted. The surface is not protected from the elements. |
|
To achieve the proper consistency for use by brush role or spray gun what is added to paint? |
Thinner |
|
What whir pigment has the highest know hiding power? |
Titanium dioxide |
|
What are the substances used as paint extenders? |
Inert chemical pigments. |
|
Which of the following paint ingredients is usually referred to as the base? |
Vehicle |
|
Which of the following paint ingredients acts as a conveyor of oxygen and assists in the paint setting up? |
Drier |
|
The most common type of thinner is composed of? |
Mineral spirits |
|
What is the minimum number of hours oil varnishes should be allowed to dry before another coat is applied? |
24 hours |
|
On topside metal surfaces that have been taken down to bare metal. What is the minimum number of primer coats after pretreatment? |
Two |
|
Which of the following paint coverings was developed for pointing a ships bottom? |
Anticorrosive |
|
When painting a ships bottom what paint is applied after anticorrosive paint? |
Anti fouling |
|
Boot topping paint is used for what area of a ship? |
Just above and just below the waterline |
|
Within how many hours after the primer has cured should nonskid material be applied? |
24 |
|
How many coats of fire retardant paint may be applied to a surface before it loses its fire retardant properties? |
Three |
|
Bare wood that is to be painted is primed with which of the following? |
One coat of aluminum paint |
|
What is the best method of applying canvas preservative? |
Spraying |
|
Based on test data. Which of the following metals is preferred for thermal spray application? |
Aluminum |
|
Which of the following is an artificial abrasive? |
Aluminum oxide |
|
Which of the following code numbers indicates the finest size of abrasive? |
2/0 |
|
What is the first step to take in sharpening a paint scraper? |
Square the end |
|
On a properly sharpened chipping hammer. The square face should be how wide? |
1/16 to 1/8 inch |
|
Which of the following is the most useful power fool for surface perpetration? |
Portable grinder |
|
Which of the following sanders has a small fast motion that actually sands in all directions? |
Orbital sander |
|
What is the main advantage of the needle gun scaler? |
It can clean out irregular surfaces |
|
Which of the following precautions must you observe when operating an electric power tool? |
Wear protective goggles and insulated gloves |
|
Under which of the following circumstances should paint and varnish remover never be used? |
In confined spaces. Near an open flame. To clean your hands |
|
What is actually the first sign of aluminum corrosion? |
White powdery residue |
|
Which of the following methods should be used to prevent corrosion when aluminum is joined to wood? |
Coat wood with one coat of spar varnish. And place insulation rape between the two surfaces |
|
Which of the following is the best system for mixing paint? |
Vibrating shaker |
|
The process of pouring pint back and fourth between two cans is called? |
Boxing |
|
Pints located in paint storage spaces should be turned upside down at least once every? |
3 months |
|
What should be done with paint that has become unfit for use? |
It should be returned to the ship yard where it can be reworked |
|
Which of the following brushed should you use to paint a large surface? |
Flat paintbrush |
|
To make brushes more flexible and easier to clean. They should be soaked for about 40 hours in? |
Boiled linseed oil |
|
After cleaning a paintbrush that is used frequently. How should you stow it? |
Wrap it in waxed paper and stow it flat |
|
What is the recommended cleaner for a brush that was used for shellac? |
Alcohol |
|
When you are applying paint to the brush. Approximately how much of the brush should be dipped into the paint? |
1/2 the length of the bristles |
|
When a surface is being painted. What is the purpose of laying in and laying off? |
To distribute the paint evenly over the surfaces |
|
The best way to ft in with a paintbrush is to move the brush? |
Swiftly in long Continuous strokes |
|
What is the maximum number of coats of paint allowed for interior surfaces? |
Four |
|
At what minimum temperature may painting be started? |
32 degrees |
|
What working conditions are most harmful to the quality of paint work? |
Lack of ventilation. Low temperatures. And high humidity |
|
After a stripping job. How should you remove the masking tape? |
By pulling it off slowly diagonally back upon itself. |
|
What should you do to ensure that paint applied with a roller does not peel off? |
Apply moderate pressure to the roller. |
|
What is the normal distance to hold a spray gun from a surface to be painted? |
6-10 inches |
|
What is the first step you should take in cleaning a pressure feed spray gun? |
Back up the fluid needle adjusting screw. |
|
What should you do immediately after removing the container when you are cleaning a container type spray gun? |
Hold a cloth over the air cap and pull the trigger. |
|
Which of the following materials should never be used in standard spray gun equipment? |
Plastics |
|
What type of respirator is usually used by personnel pint tanks and voids? |
Air line |
|
When must you change the cartridge in a chemical cartridge respirator? |
When you can smell paint vapors in the mask |
|
Which of the following safety conditions must be met when personnel are painting compartments? |
Compartments must be well ventilated. Personnel using spray guns must wear respirators. Electric light bulbs must not be changed in compartments where spray painting is in progress. |
|
Which of the following operations results in a first class professional paint job? |
Proper surface preparation. Use of recommended finish. Proper application of the finish |
|
Who is responsible for Hazardous materials on board a ship? |
Everyone |
|
What does MSDS stand for when you are dealing with HM? |
Material safety data sheet |
|
Which of the following departments is responsible to make the hazardous labels for the navy? |
Department of transportation |
|
What instruction provides the details for HM in the navy? |
OPNAVINST 4110.2 |
|
How does the naval supply system command distribute the data base for HM? |
CD-ROM |
|
What is used to protect your head against blows? |
Helmets and hard hats |