Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
70 Cards in this Set
- Front
- Back
Cat lube tank capacity |
220 Gal |
|
Lubrication circuit is actuated during what phase |
During military power |
|
S580 |
Actuates both switches at 750 psi |
|
LV stroke timer clocks reset to zero at what phase. |
Final ready |
|
S581 |
3 1/2 xhead movement |
|
S582 |
9" xhead movement |
|
Metering injector ball check valve spring loaded to |
200 - 250 LBS |
|
ICCS panels |
Left wedge - go / no go, cat interlock Intermediate slope - night light push buttons Lower center - push to test switch |
|
Sealing strip tensioner |
14 1/4 +/- 1/4 |
|
Tow test cold/hot |
1500 lbs / 2500 lbs |
|
One count on the CSV counter is equivalent to ( ) axial movement of the spindle. |
0.01 inch |
|
Range of CSV |
020 - 320 |
|
CSV set relay |
R36 energized |
|
LPL solenoid energizes during what phase |
Final ready |
|
Sealing strip guide max dimension |
1.413 " |
|
Shuttle reading for replacement of connector |
3 or more exceed 1.885 " replace connector |
|
Shuttle reading for depot level disposition |
Any dog thickness less than 0.908 |
|
Max shuttle reading |
1.905 |
|
Shuttle inspected every ( ) shots |
1200 |
|
Max spacer to strip guide gap |
0.010 |
|
Max rebuilt segmented seal permissible clearance |
0.030 |
|
WB Elbow pressure |
58 - 65 |
|
WB discharge |
65 - 105 |
|
WB pressure switch |
50 +/-2 55 +/-2 |
|
NGL tracks |
AP- BC- ASA- FSA- FT- |
|
Booster pump filter is replaced when |
Pressure drop of 25 psi or more |
|
Booster pump discharge pressure |
50 psi |
|
Ret engine stuffing box switches |
S581 SA S582 SR S583 EA S589 EF |
|
Solenoids for raising and Lowering JBDs |
A - raise B - lower |
|
Shuttle can not remain in battery for longer than |
5 mins |
|
Stress welding is |
975+/- 25 for 1 hr |
|
Cable tensioner accumulator pressure |
Pre charge - 450 psi Operating - 900 psi Relief valve - 960 +/- 50 |
|
Proper grab dynos |
4000 +/- 250 psi (3750 - 4250) |
|
Bridle tensioning relief |
225 +/- 50 |
|
Cat sheave size |
9" |
|
center cylinder in buffer assembly |
Soild rod , provides automatic retract slide assy |
|
2 outer cylinders in buffer assembly |
Hollow rod, provides fluid resistance for deceleration of A/C |
|
Shock absorber in buffer assembly |
Provides uniform deceleration to prevent damage |
|
Buffer accumulator pressure |
Pre charge : 200 psi Operating: 250 - 300 psi |
|
JBDs mod 0/2 |
6 panels per jbd, 3 operating gears |
|
JBDs mod 1 |
4 panels per jbd,2 operating gears |
|
JBD fluid pressure |
90 - 110 psi |
|
JBD max temp |
210 °f |
|
JBD raising speed |
6 seconds |
|
Cat phase colors |
Cat rdy - white Mil power - green Final ready - red Fire - red |
|
DCU flow rate |
59 - 73 Gals/min |
|
DCU spring rate |
200 lbs |
|
DCU relief valve |
3100 +/- 50 psi |
|
Main hydraulic accumulator capacity |
45 Gal / 6 cubic feet |
|
Air flask capacity |
70 cubic feet of air at 2500 psi |
|
Full LV xhead travel |
15 inches ( only during maintenance) |
|
CSV encoder max difference |
+/- 1 |
|
Steam pressure cutoff switches |
Close at 20 +/- 1 psi Open ar 10 +/- 2 psi |
|
Pressure breaking orfice elbow |
3/4 (.750) |
|
Max difference between elongs |
1" |
|
Launching pistons weight must be with in |
10 lbs of each other |
|
Top 3 segments seal gap in the. |
Cylinder cover |
|
6 segments seal the gap created by the |
Cylinder slot |
|
Shuttle has how many sweeper plates and roller |
2 & 8 |
|
Number of lube injectors per cat |
54 |
|
WB capacity |
5000 Gal |
|
WB operating temp |
40 - 180°f |
|
An increase in elbow pressure may indicate a clogged |
Annulus ring |
|
A decrease in elbow pressure may indicate a clogged |
Honey comb strainer |
|
WB proper suction |
0 - (-10) |
|
DESI readout |
Date time Shot count Endspeed CSV setting |
|
Rotary ret engine motor speed |
600 rpms |
|
4 rotary ports |
Advance Retract Purge line filter Lube drain port |
|
Rotary 3 gears |
Drum Idler Screw |
|
Dump valves actuate at |
75 ft fully fwd / aft |